audioscan Verifit VF-1 Скачать руководство пользователя страница 48

Страница: 48 / 125

0611

Verifit User’s Guide Version 2.8

Page 48

Other Hearing Instrument Tests

9.1

Section overview

FastFacts 9.1: Other hearing instrument tests

9.2

Harmonic distortion

FastFacts 9.2: Harmonic distortion

In addition to the tests of ANSI S3.22, the Verifit provides the following:

Distortion

: Harmonic distortion at 2

or 3

harmonics and 2

plus 3

with input

levels varying from 60 – 90 dB SPL.

Directional

: A unique real-time broad-band test signal presented simultaneously

from left and right speakers and analysed into two separate reponse curves.

Multicurve

: 1 – 4 curves of coupler SPL or coupler gain for swept tones or pink

noise in 1/12

octaves at selected input SPL of 0 or 40 to 90 dB in 5 dB steps.

Can be used as a 1/12th octave

spectrum analyzer

by setting stimulus to 0 dB.

Battery drain

: A 10 second test of battery current drain with no acoustic input, a 1

kHz 65 dB input SPL, and an average for 90 dB input SPL at the HFA or SPA
frequencies selected in Setup.

Manual control

: Coupler and HIT reference mic. SPL at selected 1/12

octave

frequencies and stimulus SPL of 0 and 40 – 90 dB in 5 dB steps. Can be used as
a dual channel

sound level meter

with 1/12

octave, A and C filters.

This section covers the following topics:

9.2: Harmonic distortion

9.8: Multicurve results

9.3: Directional function test

9.9: Spectral analysis in Multicurve

9.4: Directional ITE positioning

9.10: Battery drain

9.5: Directional BTE positioning

9.11: Manual control procedure

9.6: Directional HIT procedure

9.12: Sound level meter using manual control

9.7: Multicurve procedure

This test measures harmonic distortion at 2

or 3

harmonics with input levels

varying from 60 – 90 dB SPL. It also presents the sum of 2

and 3

harmonics as

total harmonic distortion (THD). For hearing aids, this differs little from true THD.

Press <Tests>, then highlight and <PICK> [Distortion].

Refer to

7.11: Coupling the hearing instrument

7.12: Positioning the hearing

instrument

and

2.6: Battery pill use and care

to prepare the instrument.

3) Turn the hearing instrument ON

Highlight and <Pick> [Start test].

Highlight and <PICK> [Harmonics], then highlight and <PICK> THD, 2nd or 3

from the drop-down list.

Highlight and <PICK> [Input], then highlight and <PICK> the desired input level
(60 – 90 dB SPL) from the drop-down list.

Press <Continue> to run the test. Distortion will be displayed at 1/3 octaves in
graphic and in tabular form.

Содержание Verifit VF-1






























































































































Результаты поиска

Содержание Verifit VF-1

Отзывы:

Бренды по названию

Популярные бренды

audioscan Verifit VF-1, Руководство пользователя

Результаты поиска

Содержание Verifit VF-1

Отзывы:

Бренды по названию

Популярные бренды