User's Manual
5. MediaPack Configuration Tools
Version 2.2
71
July 2007
5.3.5
Configuring the System
This section provides an overview of the system configuration using CLI. For a detailed
description of the CLI parameters, refer to Chapter
6.
¾
To access the Main Configuration mode:
1.
Log on to the system.
2.
Type the
enable
command to acquire administrative privileges.
3.
Type the
configure
command to enter the main configuration mode.
Table
5-3
on page
71
describes the CLI configuration modes.
Table
5-3: Description of Configuration Modes
Configuration Mode
Description
“main configuration mode”
The main configuration mode contains system wide configurations such as
DNS, SNMP, and SNTP parameters.
“context ip”
Entered from “main configuration mode”. This mode contains IP-related
configurations such as:
Static routes (refer to Section '
Static Routes
' on page
123
)
Definition of the IP interfaces (LAN and WAN). They must be defined
in this mode and are referenced in other configuration modes
“context cs”
Entered from the "main configuration" mode.
This mode contains the definitions of the logical interfaces required for call
handling by providing access to the “sip interface” and “pstn interface”
modes.
“Interface sip”
To enter the “interface sip” mode, change to the “context cs” mode, and
then use the command “interface sip sip”. This mode contains the Proxy
and Registrar definitions.
For a detailed description of parameters, refer to '
SIP Proxy & Registration
' on page
82
.
“interface isdn”
To enter the “interface pstn” mode, change to the “context cs” mode, and
then use the command “interface pstn <0..3>”.
This mode is used to configure the ISDN interface, which is a logical
abstraction used for call routing.
For a detailed list of parameters, refer to '
ISDN Interface'
on page
96
.
“gateway sip”
From the main configuration mode, use the command “gateway sip”. This
mode is used to configure general SIP-related parameters.
For a detailed description of the parameters, refer '
SIP General
'
on page
80
.
“port ethernet”
From the main configuration mode, use the command “port Ethernet 0
<0..1>”. Use 0 for the Ethernet port that corresponds to the LAN interface
and 1 for the Ethernet port that corresponds to the WAN interface.
This mode is used to configure the LAN and WAN ports (e.g., to configure
the physical connection mode).
In this mode, the media characteristics of the Ethernet port are defined. For
more information, refer to '
IP '
on page
118
.
Содержание MediaPack MP-40 series
