![ATX 22 Type-S Скачать руководство пользователя страница 88](http://html1.mh-extra.com/html/atx/22-type-s/22-type-s_owners-manual_3006274088.webp)
CARE AND MAINTENANCE
|
87
SLINGING/LIFTING THE BOAT
To prevent structural damage to your ATX boat, the proper procedure must be
used when lifting your boat . Only use appropriate style lifting slings or lift rings
with a spreader bar . Protect the rub rail to prevent any part of the lift device
from making contact with the boat .
If the boat is to be removed from the water without a trailer, follow
these guidelines:
•
Never attach lifting cables to cleats, ski tow eyes or handrails . Attach cables
only to the bow and stern eyes .
•
Cover lifting cables with rubber hose or other protectors to prevent
damage to the finish .
•
Attach guide lines to the bow and stern to control movement .
•
Use spreader bars and keep lifting pressure vertical to prevent
gunwale damage .
•
Keep the bow slightly higher than the stern to prevent engine damage .
Using Lifting Slings
This method should only be used by a qualified person with knowledge on
how to use lifting slings, or your ATX Dealer . Slings must be the flat, widebelt-
ing type .
DO NOT use cable-type slings.
The spreader bars used with the slings must be wide enough to avoid pres-
sure to the gunwales .
Contact your ATX Dealer to identify the proper location for slings . Slings may need
to be adjusted fore or aft for your particular boat .
Storage Cradle
If you are planning on storing your ATX boat on a cradle, only use a storage cra-
dle . You may also use the trailer designed for your boat to store your boat when
it is not in the water . A storage cradle or your boat’s trailer will provide proper
support and prevent stress on the hull .
Position the storage cradle as close to the sling locations as possible . Use cau-
tion not to damage any underwater components .
The storage cradle must completely touch the hull for proper support . Be sure
there are no gaps between the cradle and the hull . Store your boat with the bow
slightly elevated to the same attitude as if the boat were floating . If the boat is
stored with the bow down, moisture cannot move to the engine bilge area and
out of the boat . Remove the transom drain plug .
Make sure all compartments in the bilge area completely drain . Mold and mil-
dew can form as a result of moisture .
After the boat has been properly positioned on a storage cradle, thoroughly
wash the interior, hull, deck and interior compartments . Allow a couple of days
of air drying before covering the boat, store all cushions in the open position
and open all storage areas to help prevent mold/mildew .
Cover the boat with the storage cover . If a temporary poly cover such as
shrink wrap is used, your ATX Dealer will install vents to provide ventilation to
help prevent mold or mildew .
STORAGE/WINTERIZATION
Preparing for winter lay-up is important . In frigid zones, be particularly attentive
to items that can be damaged by freezing . Damage to your boat from improper
storage is not covered by the warranty .
Without proper preparation, storage for long periods of time can cause inter-
nal parts of the engine and drive system to rust because of lack of lubrication .
Or, if the boat is stored in below freezing temperatures, water inside the bilge or
cooling system can freeze, causing damage . The following procedures should help
prevent damage to your boat .
Perform all annual maintenance at this time .
Содержание 22 Type-S
