EmailPassword sets the password used to authenticate the login
to the SMTP email server. The password must not be more than
64 characters. A password is not required if the email server does
not require authentication.
set EmailPassword
EmailServerAddress (OEM Configurable, Supported In-Band)
EmailServerAddress configures the address of the server that
should be contacted in order to send out emails. Either an IP
address or a fully qualified domain (e.g. mail.myserver.com) may
be specified.
set EmailServerAddress [IP address]
get EmailServerAddress
EmailUsername (OEM Configurable, Supported In-Band)
EmailUsername sets the username used to authenticate the login
to the SMTP email server. The username must not be more than
128 characters. A username is not required if the email server
does not require authentication.
set EmailUsername [username]
get EmailUsername
EthernetSpeed (OEM Configurable, Supported In-Band)
EthernetSpeed determines the speed of any Ethernet port(s). If
Auto is enabled then the Ethernet speed will be negotiated and
the value in parentheses returned by the 'get' command indicates
the current speed of the Ethernet connection.
set EthernetSpeed [mp[n]] [10 | 100 | 1000 | auto]
get EthernetSpeed [mp[n] | all]
EthPortList (Supported In-Band)
Lists the available Ethernet ports and their current status. Valid
status values are: Up or Down
EthPortList
Exit
Exit terminates the current CLI session over SSH. This command has
no effect if used during a serial RS-232 session.
Exit
FCCorePresent (Supported In-Band)
Reports whether a Fibre Channel FW
diagnostics
core is present
in onboard memory.
FCCorePresent
FCDataRate (OEM Configurable, Supported In-Band)
FCDataRate specifies the Fibre Channel data rate (7550:
4/8/16Gb; 7600: 8/16/32Gb) or auto-negotiation to the highest
speed (auto).
(7550) set FCDataRate [fp | all] [4Gb | 8Gb | 16Gb | auto]
(7600) set FCDataRate [fp | all] [8Gb | 16Gb | 32Gb | auto]
get FCDataRate [fp | all]
FCLUNName (OEM Configurable, Supported In-Band)
Assigns human-readable names to FC LUNs. Names may be up to
32 characters long and may only contain upper and lower case
letters, numbers, underscores, dashes, and spaces. If the name
contains spaces, it must be enclosed in quotation marks. All LUN
names may be cleared with "set" specifying "all" with a blank
name (i.e. ""), or by issuing any of the following commands:
DeleteAllMaps, RestoreConfiguration (with the "default" option
specified), or SASMapByTopology. Note that issuing the
command Automap may result in mismatched LUNs and LUN
names.
set FCLUNName [LUN | all] [name]
get FCLUNName [LUN | all]
FCPortErrors (Supported In-Band)
FCPortErrors displays the number of Fibre Channel errors that have
occurred since the last reboot/power-on or
command at the Fibre Channel controller level.
get FCPortErrors [fp | all]
FCPortList (Supported In-Band)
FCPortList returns a list of available FC ports and their current
status. Valid status values are Up, Down, Failed, Reserved and
Disabled.
FCPortList
FCSCSIBusyStatus (OEM Configurable, Supported In-Band)
This option controls reporting of
either a ‘BUSY’ or ‘QUEUE FULL’
status at a point in time when SCSI commands cannot be
accepted.
set FCSCSIBusyStatus [busy | qfull]
get FCSCSIBusyStatus
FCSFPInfo (Supported In-Band)
FCSFPInfo displays information about the specified Fibre Channel
SFP.
get FCSFPInfo [fp | all]
