manualshive.com logo in svg

Atmel AT91FR40162S, Руководство пользователя

Продукт Atmel AT91FR40162S - это микроконтроллер с богатым функционалом и высокой производительностью. На нашем сайте вы можете скачать бесплатно руководство пользователя для этого устройства. Получите подробную информацию и инструкции по эксплуатации на {сайт}.

Поделиться
Скачать
background image

 6

6174B–ATARM–07-Nov-05

AT91FR40162S Preliminary 

5.

Architectural Overview

The AT91FR40162S integrates Atmel’s AT91R40008 ARM Thumb processor and a 2-Mbyte 
(16-Mbit) Flash memory die in a single compact 121-ball BGA package. The address, data and 
control signals, except the Flash memory enable, are internally interconnected.

The AT91R40008 architecture consists of two main buses, the Advanced System Bus (ASB) 
and the Advanced Peripheral Bus (APB). Designed for maximum performance and controlled by 
the memory controller, the ASB interfaces the ARM7TDMI processor with the on-chip 32-bit 
SRAM memory, the External Bus Interface (EBI) connected to the encapsulated Flash and the 
AMBA

™

 Bridge. The AMBA Bridge drives the APB, which is designed for accesses to on-chip 

peripherals and optimized for low power consumption.

The AT91FR40162S implements the ICE port of the ARM7TDMI processor on dedicated pins, 
offering a complete, low-cost and easy-to-use debug solution for target debugging.

5.1

Memories

The AT91FR40162S embeds 256K bytes of internal SRAM. The internal memory is directly con-
nected to the 32-bit data bus and is single-cycle accessible. This provides maximum 
performance of 67 MIPS at 75 MHz by using the ARM instruction set of the processor, minimiz-
ing system power consumption and improving on the performance of separate memory 
solutions.

The AT91FR40162S features an External Bus Interface (EBI), which enables connection of 
external memories and application-specific peripherals. The EBI supports 8- or 16-bit devices 
and can use two 8-bit devices to emulate a single 16-bit device. The EBI implements the early 
read protocol, enabling faster memory accesses than standard memory interfaces. 

The AT91FR40162S encapsulates a Flash memory organized as 1024K 16-bit words, accessed 
via the EBI. A 16-bit Thumb instruction can be loaded from Flash memory in a single access. 
Separate MCU and Flash memory reset inputs (NRST and NRSTF) are provided for maximum 
flexibility. The user is thus free to tailor the reset operation to the application.

The AT91FR40162S integrates resident boot software called AT91 Flash Memory Uploader 
software in the encapsulated Flash. The AT91 Flash Memory Uploader software is able to 
upload program application software into its Flash memory.

5.2

Peripherals

The AT91FR40162S integrates several peripherals, which are classified as system or user 
peripherals.

All on-chip peripherals are 32-bit accessible by the AMBA Bridge, and can be programmed with 
a minimum number of instructions. The peripheral register set is composed of control, mode, 
data, status and enable/disable/status registers.

An on-chip Peripheral Data Controller (PDC) transfers data between the on-chip USARTs and 
on- and off-chip memory address space without processor intervention. Most importantly, the 
PDC removes the processor interrupt handling overhead, making it possible to transfer up to 
64K contiguous bytes without reprogramming the start address, thus increasing the perfor-
mance of the microcontroller, and reducing the power consumption.

Содержание AT91FR40162S



















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AT91FR40162S

Yardney Synergy Quick Start Manual preview
Synergy
Бренд: Yardney Страницы: 8
Jetline 9600 Series Operation Manual preview
9600 Series
Бренд: Jetline Страницы: 58
Hach sc200 Software Update preview
sc200
Бренд: Hach Страницы: 2
Hach ORBISPHERE 410 Quick Operator'S Manual preview
ORBISPHERE 410
Бренд: Hach Страницы: 12
Hach AS950 AWRS Basic Operations preview
AS950 AWRS
Бренд: Hach Страницы: 472
Hach sc1000 User Manual preview
sc1000
Бренд: Hach Страницы: 64
Hach SC4500 Basic User Manual preview
SC4500
Бренд: Hach Страницы: 210
Unipower PCM500 Series Operating Manual preview
PCM500 Series
Бренд: Unipower Страницы: 24
Zamel Extra Free RZB-02 Quick Manual preview
Extra Free RZB-02
Бренд: Zamel Страницы: 2
I-Tork PDS Series Installation & Operation Manual preview
PDS Series
Бренд: I-Tork Страницы: 15
Technische Alternative UVR 63H Operation And Installation Manual preview
UVR 63H
Бренд: Technische Alternative Страницы: 68
Case IH MAXXUM 100 Service Manual preview
MAXXUM 100
Бренд: Case IH Страницы: 81
EuroLite Ambience Control 1 User Manual preview
Ambience Control 1
Бренд: EuroLite Страницы: 20
SKF Matrix MAX1 Installation, Operation And Maintenance Manual preview
Matrix MAX1
Бренд: SKF Страницы: 88
Powtran PR5200 011G3 User Manual preview
PR5200 011G3
Бренд: Powtran Страницы: 40
Samson TROVIS 5571 Mounting And Operating Instructions preview
TROVIS 5571
Бренд: Samson Страницы: 44
Beckhoff C6925 Manual preview
C6925
Бренд: Beckhoff Страницы: 47
DOTECH FX3DH Series Manual preview
FX3DH Series
Бренд: DOTECH Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды