Atlas XENOTEST BETA+ Скачать руководство пользователя страница 51

Страница: 51 / 60

Operating instructions XENOTEST BETA+

Troubleshooting

Tab. 5-2

Error message

Correction

Low water level, reservoir

Top up reservoir

Sample chamber door open.

Close sample chamber door.

Device cover open.

Close device cover.

Sample chamber overtemperature.

Contact Technical Service

Irradiator exhaust air overtemperature.

Contact Technical Service

Series device overload.

Contact Technical Service

Sample chamber air recirculation faulty.

Contact Technical Service

Sprinkler failure.

Contact Technical Service

Humidification failure.

Contact Technical Service

Battery missing or discharged.

Contact Technical Service

Battery older than 5 years.

Contact Technical Service upon next inspection.

Low water level, humidifier.

Check the tubing and connections.
Check the filling level in the reservoir.

XENOSENSIV sensor or terminating
plug not installed.

Check that the XENOSENSIV sensor or terminating plug are
installed.

Check the xenon bulb seat.
Check the xenon bulb fuse.
Check the xenon bulb`s age.

Lamp will not ignite.

Contact Technical Service. The device remains operative.

Reenter program, time and filter system.

Memory error
Performing basic inizilisation
--> ENTER
All device data and calibration factors
deleted --> ENTER
Power failure
on dd.mm.yy. at hh:mm

Refer to the software documentation.
Resume interrupted program by inputting the appropriate data.

Содержание XENOTEST BETA+





























































Результаты поиска

Содержание XENOTEST BETA+

Отзывы:

Похожие инструкции для XENOTEST BETA+

Бренды по названию

Популярные бренды

Atlas XENOTEST BETA+, Руководство по эксплуатации

Результаты поиска

Содержание XENOTEST BETA+

Отзывы:

Похожие инструкции для XENOTEST BETA+

Бренды по названию

Популярные бренды