12
NOTE
: Once you select the start button an audible exit alarm will begin to sound and the
Sanidyne
®
Prime Remote
will begin counting down from 1:30 seconds to allow all inhabitants to leave the area before the UV treatment begins.
The words “LEAVE AREA
” will now appear on the lower status bar of the Hand-held Remote Controller. (See Figure
3, for the specific location). The Occupancy Sensors located on the top of the unit (Shown on Figure 1) will begin to
operate at this time, providing an additional safety area around the unit. If the sensors detect movement close to the
Sanidyne
®
Prime Remote
when less than 30 seconds remains on the countdown time, the
Sanidyne
®
Prime Remote
will automatically reset giving 30 seconds more to leave the Operation Area. The Countdown time as well as the Treatment
Time will all be displayed on the Hand-held Remote Controller. See Figure 3, for the specific location.
Occupancy Sensors do not protect the entire Operation Area of the
Sanidyne
®
Prime Remote
. Under no
circumstances should this unit be permitted to operate with human, or animals present in the Operation Area.
4.
The Hand-held Remote Controller displays the Lamp Status; When the lamp operation indicators on the display glow yellow
the lamp is on, when the lamp is off it displays grey. (See
Figure 3
to locate lamp operation indicators) Once the treatment
time has expired the unit will turn off the Germicidal Ultraviolet Lamps and it is now safe to return to the area.
If at any time during the Treatment Time the Occupancy Sensors detect someone near the
Sanidyne
®
Prime Remote
, the unit will immediately turn off and send an alarm to the Hand-held Remote Controller and
the
Sanidyne
®
Prime Remote
. If this event occurs the alarm can be turned off on the remote by pressing anywhere on the
display or at the
Sanidyne
®
Prime Remote
by pressing the START/STOP
on the Keypad. If the Alarm is turned off at the
Sanidyne
®
Prime Remote
the operator can reset the unit by pressing the START/STOP button on the keypad controller
again to begin the 1:30 countdown to allow all inhabitants to leave the area. After the 1:30 has elapsed the unit will power
on and complete the remaining Treatment Time left prior to the alarm.
If the Hand-held remote is used to stop the alarm, the operator must return to the area and ensure that the area is safe to
proceed. Select the START/STOP button on the keypad controller to begin the 1:30 countdown to allow all inhabitants
to leave the are. After the 1:30 has elapsed the
Sanidyne
®
Prime Remote
will power on and complete the remaining
Treatment Time left prior the alarm.
s
etting
D
ate
anD
t
ime
Option 1 – Using the tablet’s Settings menu:
1. Navigate to the tablet’s settings menu by tapping the
Settings
icon on the Home Screen or in the App Directory.
2.
Scroll down to
Date & Time
under
System
.
3. Use the
Set Date
,
Set Time
, and
Select Time Zone
functions to set the correct date and time.
Option 2 – If starting in the LampControl app Settings menu:
1. Press the
Settings
Button. (See
“Hand-Held Remote Controller Overview”
on
pages 8–9
.)
2. Press
Set Date/Tim
e.
3. Press
Admin Pin
. Using keyboard, enter Pin number 1234. (This will bring you to the tablet’s
Settings
menu.)
4.
Scroll down to
Date & Time
under
System
.
5. Use the
Set Date
,
Set Time
, and
Select Time Zone
functions to set the correct date and time.
s
aving
a
s
ession
Saving a Session: At the end of a Session or after a Session is Stopped the
“Save This Session”
box will appear.
To save a Session:
1. Press
Yes
under Save Session.
2. Press on
Note Entry
3. Type in Session Notes, press
OK
Clearing Total Op Time or Clearing Session Data:
1. Press
Settings
Button
2. Press
Settings
3.
Press on the box next to
“Reset Total Operating Time”
and/or
“Clear Session Data.”
4. Press
Home
Button.
