11
s
aniDyne
®
P
rime
r
emote
o
Peration
The
Sanidyne
®
Prime Remote
has two methods of controlling the unit; the Keypad Controller (Shown in
Figure 2
) and the
Hand-held Remote Controller (Shown in
Figure 3
). These two controls mirror each other; treatment times entered into Keypad
Controller will appear on the Hand-held Remote Controller and vice versa.
u
sing
tHe
K
eyPaD
C
ontroller
to
s
et
t
reatment
t
imes
1.
Setting Treatment Time on the Keypad is done using the
HOURS
and
MINUTES
buttons which are located on the top of
the unit. (See
Figure 1
for location) Selecting the up or down facing arrows located on the keypad in line with the
HOURS
or
MINUTES
button will either increase or decrease the hours or minutes. The hours can be set between 0 and 24, and
the minutes can be set from 1 to 59. (Example of one hour and five minutes would appear as 01:05 on the Treatment Time
Display). Since the Keypad Controller will no longer be viewable once the treatment time begins, it is recommended that the
Hand-held Remote Controller be fully charged and powered before this time and be in possession of the operator at all times.
2.
Determining the proper treatment times for your specific location can be done by using the
“Recommended Treatment Time
for Room Size”
chart (
Figure 4
on
Page 13
).
3.
Once the choice of time has been displayed on the Keypad controller, select the
START/STOP
button to begin and leave the
Operation Area immediately. Make sure that the Hand-held Remote Controller is kept in possession of the operator during the
Treatment Time.
Once you select the START/STOP
button an audible exit alarm will begin to sound and the
Sanidyne
®
Prime
Remote
will begin counting down from 1:30 seconds to allow all inhabitants to leave the area before the UV treatment
begins. Additionally, the word “PrEP” will begin flashing on the Keypad and the Occupancy Sensors located on the
top of the unit (Shown on Figure 1) will begin to operate at this time, providing an additional safety area around the
unit. As an additional safety feature, if the sensors detect movement close to the
Sanidyne
®
Prime Remote
when
less than 30 seconds remain on the countdown time, the
Sanidyne
®
Prime Remote
will automatically reset giving 30
seconds more to leave the Operation Area.
Occupancy Sensors do not protect the entire Operation Area of the
Sanidyne
®
Prime Remote
. Under no
circumstances should this sanitizer be permitted to operate with humans, plants, or animals present in the Operation Area
.
4.
Outside the Operation Area the Treatment Time can be viewed on the Hand-held Remote Controller. Once the treatment time
has expired the unit will turn off the
STER-L-RAY
®
Germicidal Ultraviolet Lamps and it is now safe to return to the area.
The word
“donE”
will begin flashing on the Keypad Controller on the top of the unit.
u
sing
tHe
H
anD
-
HelD
r
emote
C
ontroller
to
s
et
t
reatment
t
imes
The Hand-held Remote Controller provides further detailed information on the
Sanidyne
®
Prime Remote
. Therefore it is
recommended to review the Hand-held Remote Controller Overview section of this manual to become familiar with the display
which is shown in
Figure 3
.
The Hand-held Remote Controller can operate the
Sanidyne
®
Prime Remote
remotely, thus it is
imperative that the operator make a visual inspection of the Operation Area to ensure it is clear of all humans, plants, or
animals before proceeding.
1.
Setting Treatment Time on the Hand-held Remote Controller is done by holding a finger on the display face, directly on the
words Treatment Time until the screen changes to a scroll bar. Next scroll the numbers up or down, characters on the left are
hours, characters on the right are minutes. Positioning the desired treatment time in the center row. (Example of one hour and
five minutes would appear as 01:05 on the Treatment Time Display) When times are positioned correctly, select
DONE
on the
bottom of the scroll bar to input your Treatment Time choice.
2.
Determining the proper treatment times for your specific location can be done by using the
“Recommended Treatment Time
for Room Size”
chart (
Figure 4
on
Page 13
).
3.
Once the choice of time has been displayed on the Hand-held Remote Controller, select the start button to begin and leave the
Operation Area immediately. Make sure that the Hand-held Remote Controller is kept in possession of the operator during the
Treatment Time.
(Remote Controller Instructions Continued on Page 12)
