Ascon tecnologic KM5P Series Скачать руководство пользователя страница 6

Ascon Tecnologic - KM5P Line - ENGINEERING MANUAL - PAG. 6

5  CONFIGURATION PROCEDURE

5.1  Introduction

When the instrument is powered, it starts immediately to work 
according to the parameters values loaded in its memory.
The instrument behaviour and its performance are governed 
by the value of the stored parameters.
At the first start up the instrument will use a “default” parameter 
set (factory parameter set); this set is a generic one (e.g. a TC 
J input is programmed).

Before connecting the output actuators

,  

we recommend to configure the parameters to suit 
your application (e.g.: input type, Control strategy, 
alarms, etc.).

To change these parameters you need to enter the 
“Configuration mode”.

Do not change the 

[6] Unit

 (Engineering Unit) value 

during process control as the temperature values 
inserted by the user (thresholds, limits etc.) are not 
automatically rescaled by the instrument.

5.2  Instrument behaviour at Power ON

At power ON the instrument can start in one of the following 
mode depending on its configuration:

Auto mode

 without program functions.

 

The upper display will show the measured value;

 

The lower display will show the Set point value;

 

The decimal figure of the less significant digit of the upper 
display is OFF;

 

The instrument is performing the standard closed loop control.

Manual mode

 (OPLO).

 

The upper display will show the measured value;

 

The lower display will show the power output and the MAN 
LED will lite;

 

The instrument does not perform Automatic control;

 

The control output is equal to 0% and can be manually 
modified by 

 and 

 buttons.

Stand-by mode

 (St.bY).

 

The upper display will show the measured value;

 

The lower display will show alternately the set point value 
and the message 

St.bY

 or 

od

;

 

The instrument does not perform any control (the control 
outputs are OFF);

 

The instrument is working as an indicator.

Auto mode 

with automatic program start up.

 

The upper display will show the measured value;

 

The lower display will show one of the following information;

•  The operative set point (when it is performing a ramp)
•  The time of the segment in progress (when it is perform-

ing a soak);

NOTE VERY WELL

: In all cases, the decimal figure of the 

less significant digit of the lower display is lit.
We define all the above described conditions as “

Standard 

Display

”.

5.3 

Entering the “Configuration modes”

The configuration parameters are collected in various 
groups.  Every group defines all parameters related with a 
specific function (e.g.: control, alarms, output functions).

1. 

Push the 

 button for more than 5 seconds. 

The upper display shows 

PASS

 while the lower display 

shows 

0

.

2. 

Using 

 and 

 buttons set the programmed password.

Notes:   1. 

The factory default password for configuration 
parameters is equal to 30.

2. 

During parameter modification the instrument 
continues to control the process. 
In certain conditions, when a configuration 
change can produce a heavy bump to the 
process, it is advisable to temporarily stop the 
control during the programming operations (the 
control output will be Off).  In this case, use a 
password equal to 2000 + the programmed value 
(e.g. 2000 + 30 = 2030). 
The control will restart automatically when the 
configuration procedure will be manually closed.

3. 

Push the 

 button. 

If the password is correct the display will show the acronym 
of the first parameter group preceded by the symbol: 

]

In other words the upper display will show: 

]inp

 

(group of the 

Input parameters

).

The instrument is in configuration mode.

5.4  Exiting the “Configuration mode”

Push 

 button for more than 5 seconds, the instrument will 

come back to the “standard display”.

5.5  Keyboard functions during 

parameter changing

  A short pression on the button exits from the current 

parameter group and selects a new parameter group.

 

A long pression allows to close the configuration 
parameter procedure (the instrument returns to the 
“standard display”).

  When the upper display is showing a group and the 

lower display is blank, this key allows to enter in the 
selected group.

 

When the upper display is showing a parameter and 
the lower display is showing its value, this key allows 
to store the selected value for the current parameter 
and access the next parameter within the same group.

  Increases the value of the selected parameter.
  Decreases the value of the selected parameter.
 + 

  These two keys allow to return to the previous 

group.  Proceed as follows: 

 

Push the 

 button and maintaining the pressure, 

push the 

 button; release both the buttons.

Note: 

The group selection is cyclic as well as the selection 
of the parameters in a group.

Содержание KM5P Series













































Отзывы: