AS MOTOR AS-751 RC Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 49

background image

Page 41 / 49

Tightening of belt between motor and coupling

Tighten the belts in the following way:

1.

Slacken the four bolts that are holding the motor.

2.

Slacken the lock nuts in the adjusting mounting.

3.

Adjust the nuts until the correct belt tension is obtained.

4.

Check with a guide rail if the pulley of the motor is parallel with the coupling. If it isn’t,
adjust with the nuts. Then check the belt tension.

5.

Retighten the motor bolts and the lock nuts.

Tightening of belt between motor and hydraulic pump

Tightening of the belt is carried out the following way:

1.

Slacken the two bolts that are holding the pump.

2.

Slacken the lock nut on the adjusting bolt.

3.

Adjust the nut on the adjusting bolt until the correct belt tension is obtained.

4.

Retighten the pump bolts and the lock nuts.

Siting of motor
bolts

Adjustning nut for belt
tightening

Lock nut

Bolts for pump

Adjusting bolt

«
...
39
40
41
42
43
...
»

Содержание AS-751 RC


















































Отзывы:

Нет отзывов

Похожие инструкции для AS-751 RC

Бренд: Flymo Страницы: 11

Бренд: Texas Страницы: 60

NZMX30614KH, NZMX32734BV

Бренд: Snapper Страницы: 13

Бренд: Snapper Страницы: 28

Бренд: Yazoo/Kees Страницы: 19

Бренд: Yard-Man Страницы: 6

Бренд: Worx Страницы: 64

Бренд: Bad Boy Страницы: 48

Enviromower ENV369B

Бренд: Victa Страницы: 28

PERFORMANCE 50562X89

Бренд: YARD KING Страницы: 60

Бренд: Craftsman Страницы: 36

Бренд: Cub Cadet Страницы: 4

Бренд: EINHELL Страницы: 84

Бренд: EINHELL Страницы: 104

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды