AS MOTOR AS-751 RC Скачать руководство пользователя | Manualshive

Страница: 42 / 49

background image

Page 42 / 49

Tightening of belt between coupling and mower

Tightening of the belt is carried out the following way:

1.

Slacken the four bolts that are holding the mower, two in each side.

2.

Slacken the lock nuts on the adjusting bolts.

3.

Adjust the nut on the adjusting bolt until the correct belt tension is obtained.

4.

Check with a guide rail, if the pulley of the mower is parallel with the coupling.
Adjust with the nuts if it isn’t. Then check the belt tension.

5.

Retighten the bolts and lock nuts for the mower.

Adjusting bolt Bolts for mower

Guide rail

«
...
40
41
42
43
44
...
»

Содержание AS-751 RC


















































Отзывы:

Нет отзывов

Похожие инструкции для AS-751 RC

Бренд: Lawn-Boy Страницы: 32

Бренд: Nakayama Страницы: 12

MOW'N MACHINE FZ22-2

Бренд: Woods Страницы: 48

Бренд: Parker Страницы: 25

Бренд: Yard-Man Страницы: 4

Бренд: Ryobi Страницы: 16

Бренд: SaMASZ Страницы: 52

Бренд: Toro Страницы: 60

Бренд: AL-KO Страницы: 304

Бренд: Sabo Страницы: 88

Бренд: Cub Cadet Страницы: 24

Бренд: Craftsman Страницы: 20

Бренд: Husqvarna Страницы: 11

Бренд: Husqvarna Страницы: 24

Бренд: Husqvarna Страницы: 24

Бренд: Husqvarna Страницы: 40

PZ5426FX / 966614001

Бренд: Husqvarna Страницы: 34

Бренд: Husqvarna Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды