ARTE NIREAS, Инструкция по установке и эксплуатации

Страница: 21 / 30

I
NSTALLATION
&
USER MANUAL
WATER HEATING FIREPLACE
| NIREAS
20 | Page
8. L
IGHTING THE FIREPLACE
8.1. Traditional method of lighting
Every time you light the fireplace, it initially requires large volumes of air. When the fireplace is cold, leave the door slightly open in order for air
to circulate around the door for the first few minutes and turn the fader (STANDARD system) clockwise
(Table 7.2.1, Line 6)
at the maximum
open setting.
To form an adequate layer of ash at the base of the fireplace, use 1-2 kg of dry kindling the first time you light it. If it is possible, constantly
maintain a layer of ash with thickness of 2-3 cm at the base of the combustion chamber for added insulation.
1. Place 2-4 kindling tablets or 7-10 wrapped newspaper sheets beneath 1-2 kg dry kindling.
2.
Turn the fader (STANDARD system) clockwise
(Table 7.2.1, Line 6)
at the maximum open setting.
3.
After the the ignition of the tablets/wrapped sheets, leave the door slightly open, in order to ensure an adequate convection of the flue.
4.
Once you ensure the flue is warm enough (after 5-10 minutes), close the door. If all required conditions are met, after 15-20 minutes a thick
layer of cinder will be formed in the combustion chamber and the temperature will rise, which is essential for the continuation of
combustion.
5.
Once the requirement described in point 4 is met, place 2-3 logs with overall weight of 7.2kg, onthe cinder, with a distance of about 1cm
from one another
6.
Turn the fader (STANDARD system)
(Table 7.2.1, Line 6)
at the desired setting and close the door. The wood will begin to burn within 2-3
minutes. If not, open the door slightly in order for enough air for combustion to enter. Close the door again once the wood ignites.
7.
Ensure there is adequate air supply (oxygen) to maintain the flame clear and powerful when you reduce the amount of combustion air
and after.
8.
As soon as the fire leaves a thick layer of cinder, you can add more firewood by repeating steps 5-7.
8.2. Lighting without CO emissions (FROM TOP TO BOTTOM)
1.
Turn the fader (STANDARD system) clockwise
(Table 7.2.1, Line 6)
at the maximum open setting. If needed, leave the door slightly in order
to ensure an adequate convection of the flue.
2. Place logs with overall weight of 7.2 kg and 30-50 cm verticaly, on the back of the fireplace.
3.
Place 2-3 kindling tablets or 5-8 wrapped newspaper sheets between the logs.
4.
Add a few twigs (1-2 kg) on the top in zigzag arrangement.
5.
Finally, place a medium log on top of the stack and light the tablets/wrapped sheets.
6. Once you ensure the flue is warm enough (after 5-10 minutes), close the door.
7. Turn the fader (STANDARD system) (Table 7.2.1, Line 6) at the desired setting, so as to ensure there is adequate air supply (oxygen) to
maintain the flame clear and powerful.
8.
As soon as the fire leaves a thick layer of cinder, you can add more firewood.
Feed the fireplace often but with small amounts of firewood, at most 7.2kg, each time. If the fireplace is overly full, the generated heat may
cause excessive strain on the flue or heat the water very much. The supply of firewood should be done in moderation.
The openings of the secondary air supply should not be covered by firewood.
To avoid covering the glass with soot, it is
important not to let logs lean against it.
Don’t leave the fireplace unattended as long as the door remains open
Due to the self-closing door you should be very careful for
any accidents during the fueling of the fireplace.