Arsenal FU 321M Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 64

Arsenal FU 321M Скачать руководство пользователя страница 7

OPERATING AND MAINTENANCE MANUAL FU 321M

4

* Be aware of the position of the emergency stop.

* Protect your hands. Stop the main spindle before proceeding to change tools
or workpiece, adjusting a new workpiece, measuring, changing or adjusting belts,
puleys or gears, removing swarf or oil, etc.

* Before starting operation make sure that the workpiece and the cuttters are well
tightened.

* Loose objects on the table may be catapulted into the air. Before starting to
work remove all loose objects such as tools, mandrels, clothes, etc.

* Arrange all tools in order of use.

* Damaged or weakened tools break easily. Keep all tools sharp. Check tools and
toolholder on a regular basis. Insert the tool as far as possible into the toolholder.

* Avoid tool breakage.Use suitable machining feeds and speeds. Reduce speed and
feed when unusual noises are noticed. Avoid unnecessary damage to tool and/or
workpiece. Never start the machine when the tool is touching the workpiece. After
mounting the tool, carry out a trial run. Do not operate the machine in automatic
mode in the beginning.

* Do not use compressed air to clean or remove dust and swarff from the
machine and its surroundings. Use a brush or chip scraper.

* Certain materials, such as magnetisium are highly inflammable in powder or
chip form. Always consult a supervisor before working with these materials.

* Prevent fires. Keep inflamable material and liquid well away from the work area
and hot swarf.

* Make sure the machine is disconnected from the mains before procceding with
any type of repairs or maintenance.

* Maintenance should be carried out by qualified staff.

WARNING:

All electrical connections must be performed by a qualified electri-

cian or service engineer.

THIS DOCUMENT IS A GUIDELINE FOR THE OPERATOR. HOWEVER,
"ARSENAL" Co. DOES NOT ASSUME ANY RESPONSIBILITY FOR ANY
ACCIDENTS NOR CAN WE GUARANTEE THE AVOIDANCE OF ANY
ACCIDENTS EVEN IF ALL SAFETY INSTRUCTIONS ARE STRICTLY
FOLLOWED AS THE TYPE OF WORK PERFORMED MAY REQUIRE
DIFFERENT SAFETY MEASURES.

«
...
5
6
7
8
9
...
»

Содержание FU 321M

































































Отзывы:

Нет отзывов