manualshive.com logo in svg

Arsenal FU 321M, Руководство по эксплуатации и техническому обслуживанию, Страница: 19 / 64

Поделиться
Скачать
Arsenal FU 321M Скачать руководство пользователя страница 19

OPERATING AND MAINTENANCE MANUAL FU 321M

16

PREPARATION FOR START - UP

Before initial operation of the machine after unpacking, or keeping the machine
idle for a long period, make a close examination and cleaning of all mechanisms,
fill the tanks with oil / Fig.8a / and coolant and connect the machine to the mains
as prescribed in the section "Electric Equipment".

The locking mechanism for the longitudinal travel 12, cross travel mechanism 14
and vertical travel mechanism 26 / Fig.3 / should be disengaged. All mechanisms
should operate smoothly and trouble - free. Check that they do that by hand.

Check the proper functioning of the gear boxes by switching from lowest to
highest gear speeds and feeds during idle running. At the same time constantly
observe the lubrication system operation through the oil level indicators.

Warm up the machine by running it for 30 minutes at idle running mode.

Proir to initial use of machine, Emergency Stop functions should be checked. To
check it start the spindle at max speed. After 10 seconds press one of the
"Emergency Stop" buttons 45 or 51 / Fig.3a / and  make a note of how long it
tooks for spindle to stop. The function of each button should be checked sepa-
rately.

Then start the machine in exactly the same way and after 10 seconds use the main
breaker 41 / Fig. 3a / to stop the spindle. Measure the time for spindle stopping.
It should take longer for spindle to stop when use the main breaker.

If the time of spindle stop is the same for both tests a qualified electrician should
be called and the problem should be eliminated immediatly before the machine is
used.

CAUTION:

1. Remember: During a power failure the dynamic spindle stop will not be
available.

2. When a vertical milling head, a slotting head or a universal milling head are
used, the vertical stroke is limited. To prevent the danger of shock move the lower
cam into the additionally machined screw hole to fix it.

3. The table swing towards the electric cabinet is limited in order to avoid the
smash of the electric cabinet due to operator's carelessness. To swing the table
to bigger angle remove the stopper placed to the outlet of support's T-slot and
look out for not smaching the electric cabinet during table traverse on axis.

See and read carefully sections "Safety precautions" and "Maitenance".

Содержание FU 321M

































































Отзывы:

Нет отзывов