Arjo E9X Скачать руководство пользователя | Manualshive

Страница: 51 / 68

background image

51

Battery test

Check the condition of the backup battery by carrying out the following test.

1. Disconnect the bed from the electricity supply.

2. Raise the mattress platform to maximum height - ignore the

battery warning tone.

3. Raise the backrest and thigh sections as far as they will go.

4. Press and hold the CPR button. The mattress platform will flatten

and lower to a mid-height position.

5. Lower the mattress platform to minimum height.

6. Apply maximum head down tilt (Trendelenburg).

7. Return the mattress platform to the level position; then apply

maximum foot down tilt (reverse Trendelenburg).

If this test is not completed successfully, connect the bed to the electricity
supply for at least eight hours to recharge the battery then perform the test
again. If the bed fails a second time, contact Arjo or an approved service
agent.

To maintain best performance, the backup battery should be replaced every
four years by an approved service agent.

«
...
49
50
51
52
53
...
»

Содержание E9X





































































Отзывы:

Нет отзывов

Похожие инструкции для E9X

Бренд: Rabe Страницы: 65

Бренд: T-Drill Страницы: 75

Бренд: Zeiss Страницы: 38

Бренд: Pall Страницы: 51

Бренд: ZAMST Страницы: 21

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: DAKO Страницы: 25

Бренд: 3M ESPE Страницы: 50

Бренд: VACGEN Страницы: 13

Бренд: Banfer Страницы: 6

Бренд: M-system Страницы: 2

Бренд: Rico Страницы: 34

Бренд: Launch Страницы: 3

Бренд: Launch Страницы: 43

Бренд: Launch Страницы: 8

Бренд: Launch Страницы: 67

Бренд: Launch Страницы: 55

Бренд: LAUNCH TECH Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды