Arjo E9X Скачать руководство пользователя

Страница: 42 / 68

Weighing

To calculate and display the patient’s weight:

1. With the patient lying centrally on the bed, press the

Weigh

button once.

2. The display will show a moving circular pattern until a stable

weight reading is obtained.

3. The patient’s weight will be displayed for ten seconds then the

display will go blank.

The patient’s weight is usually displayed rounded to the nearest 500g; this
can be temporarily changed to 100g by pressing the

Select Weight

Display

button. The display will revert to 500g next time the

Weigh

button

is pressed.

Auto
Compensation

The Auto Compensation facility allows weight (up to a maximum of 100kg)
to be added to or removed from the bed, without affecting the indicated
patient weight.

1. With the patient lying on the bed, press the

Auto Compensation

button once.

2. The display will show a moving circular pattern until a stable

weight reading is obtained.

3. The display will show

to indicate that the system is in Auto

Compensation mode.

4. Add or remove accessories, bed linen, pillows, etc. as required.

5. Press the

Auto Compensation

button again.

6. The display will show a moving circular pattern for a few seconds

then revert to showing the patient’s weight..

NOTE
The 100g weight display should only be used for comparative readings.

CAUTION

The weighing system requires periodic calibration to ensure accuracy. See
“Preventive maintenance” on page 49.

Содержание E9X





































































Результаты поиска

Содержание E9X

Отзывы:

Похожие инструкции для E9X

Бренды по названию

Популярные бренды

Arjo E9X, Инструкция по эксплуатации

Результаты поиска

Содержание E9X

Отзывы:

Похожие инструкции для E9X

Бренды по названию

Популярные бренды