P/N 466-
2915 (ML) • REV C • ISS 11DEC20
5 / 54
Menu 7, Security Mode (ATS1115-N / ATS1116-N only)
This option selects the type of user card the ATS1115-N and
ATS1116-N reader will recognise. The reader will recognise
configuration and default cards in both modes. The possible
modes are as follows:
•
Unsecured Mode (default setting): The reader will
recognise blank or un-programmed cards only, by using
the card’s unique serial number. The four-byte security
password is not used. Unsecured mode requires the use
of an expanded memory system.
•
Secured Mode: Only cards programmed on the
ATS1620/1621/1622 programmer will be recognised in
this mode. The four-byte security password is used.
Menu 8, Valid Card Flash (ATS1115-N / ATS1116-N only)
This option enables (default setting) and disables the blue LED
flash when a valid card is badged on an ATS1115-N or
ATS1116-N reader.
Menu 9, Protocol options (ATS1115-N / ATS1116-N only)
This option selects the method by which an ATS1115-N /
ATS1116-N reader sends data to the panel. The options are as
follows:
•
Wiegand: Smart Card data is transmitted in the Wiegand
protocol by default. The ATS1620/1621/1622 programmer
sets the number of bits (26- or 27-bit) when user cards are
programmed.
•
Magnetic Stripe: The reader sends data to the panel in
a 32-bit magnetic stripe card format.
•
Tecom Smart Card: This format is not implemented in the
panel and should not be selected.
Menu 10, Card Beep Options (ATS1115-N / ATS1116-
N only)
This option enables the beep sounded when a card is badged
on the reader (default setting) and disables the beep.
Menu 11, Option Card (ATS1115-N / ATS1116-N only)
This option enables (default setting) and disables the use of
reader configuration (option) cards at the ATS1115-N and
ATS1116-N reader. If an installer wishes to prevent the
modification of the reader setup by configuration card, this
option should be disabled.
Menu 12, Last Card (ATS1115-N / ATS1116-N only)
This option displays the number of the last card badged on an
ATS1115-N or ATS1116-N reader, in the format: Facility Code
/ System Code, ID Number or as raw card data (depends on
setting of security mode).
Technical data
ATS1110-N
ATS1111-N
ATS1115-N
ATS1116-N (with
smart card reader)
Supply voltage
8.5 to 14.0 V
Maximum operating current
95 mA at
13.8 V
165 mA at 13.8 V
Normal operating current (all
areas armed)
26 mA at
13.8 V
35 mA at 13.8 V
ATS1110-N
ATS1111-N
ATS1115-N
ATS1116-N (with
smart card reader)
Open collector output (
“OUT”
terminal)
15 V
max. at 50 mA max.
Wireless operating frequency
—
125 kHz
Maximum power output
—
65.7
dBµA/m
at 10 m
Dimensions with cover
(W x H x D)
92 x 165 x 25.4 mm
(3.6 x 6.5 x 1 in.)
Weight
300 g
305 g
Operating temperature
−10 to +50°C (22 to 122°F)
Humidity
< 95% non condensing
Code combinations:
5 digits
9 digits
100 000
1 000 000 000
IP rating
IP30
ACE type (tamper protection)
B
Regulatory information
Manufacturer
PLACED ON THE MARKET BY:
Carrier Fire & Security Americas Corporation Inc.
13995 Pasteur Blvd
Palm Beach Gardens, FL 33418, USA
AUTHORIZED EU REPRESENTATIVE:
Carrier Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED FOR
SALE TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. CARRIER FIRE &
SECURITY CANNOT PROVIDE ANY
ASSURANCE THAT ANY PERSON OR ENTITY
BUYING ITS PRODUCTS, INCLUDING ANY
“AUTHORIZED DEALER” OR “AUTHORIZED
RESELLER
”, IS PROPERLY TRAINED OR
EXPERIENCED TO CORRECTLY INSTALL
FIRE AND SECURITY RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/
Version
This document applies to ATS111x-N firmware
version 10 or later.
Certification
EN 50131-1 System requirements
EN 50131-3 Control and indicating equipment
Security Grade 3, Environmental class II
Tested and certified by Telefication B.V.
ATS1110-N, ATS1111-N: Carrier Fire & Security
hereby declares that this device is in compliance
with the applicable requirements and provisions of
the Directive 2014/30/EU and/or 2014/35/EU. For
more information see
www.firesecurityproducts.com
ATS1115-N, ATS1116-N: Carrier Fire & Security
hereby declares that this device is in compliance
with the applicable requirements and provisions of
all applicable rules and regulations, including but
not limited to the Directive 2014/53/EU. For more
information see www.firesecurityproducts.com
Содержание ATS111-N Series
Страница 54: ...54 54 P N 466 2915 ML REV C ISS 11DEC20 ...
