Arctic Cat S2009BCDFCOSL страница 77 Скачать руководство пользователя

Страница: 77 / 88

PREPARATION FOR STORAGE

PREPARATION FOR STORAGE

Prior to storing the snowmobile, it

must be properly serviced to prevent

corrosion and component deterioration.

An authorized Arctic Cat Snowmobile

dealer should perform this service;

however, the owner/ operator can per-

form this service if desired. This ser-

vice is at the discretion and expense of

the snowmobile owner. To prepare the

snowmobile for storage, Arctic Cat

recommends the following procedure:

1. Clean the seat cushion with a

damp cloth and a Vinyl Protectant.

2. Clean the snowmobile thoroughly

by hosing dirt, oil, grass, and other

foreign matter from the skid

frame, tunnel, hood, and belly pan.

Allow the snowmobile to dry thor-

oughly. DO NOT get water into

any part of the engine.



NOTE: On 4-stroke models,

change the engine oil and clean
the air filter; then proceed to step
6.

3. Place the rear of the snowmobile

up on a shielded safety stand.

4. On the 500/600/800/1000 cc

engine models, start the engine

and allow to idle. With the engine

idling, pry the intake boot forward;

then spray an Engine Storage Pre-

server into the intakes until the

engine exhaust starts to smoke

heavily or until the engine starts to

drop in RPM. Turn engine off.

Install the intake boot.

5. On the 570 cc engine models,

carefully pry the intake boots par-

tially over the carburetor inlets;

then start the engine and allow to

idle. With the engine idling, spray

an Engine Storage Preserver into

the intakes until the engine exhaust

starts to smoke heavily or until the

engine starts to drop in RPM. Turn

engine off. Install the intake boots.

6. Plug the exhaust system outlet

with a clean cloth.

7. With the ignition switch in the

OFF position:

A. Disconnect the high tension

leads from the spark plugs;

then remove the plugs, connect

them to the leads, and ground

them on the cylinder heads.

B. Pour 29.5 ml (1 fl oz) of SAE

#30 petroleum-based oil into

each spark plug hole and pull

the recoil starter handle slowly

about 10 times.

C. Install the spark plugs and con-

nect the high tension leads.

! CAUTION

Do not run the engine without the
belt guard in place and secured.

! CAUTION

Do not do step 7 on the 4-stroke
models; severe engine damage
could result.

! CAUTION

Never crank the engine over with-
out grounding the spark plugs.
Damage to coils and/or CDI/ECU
unit may result.

Содержание S2009BCDFCOSL

























































































Результаты поиска

Содержание S2009BCDFCOSL

Отзывы:

Похожие инструкции для S2009BCDFCOSL

Бренды по названию

Популярные бренды

Arctic Cat S2009BCDFCOSL, Руководство оператора

Результаты поиска

Содержание S2009BCDFCOSL

Отзывы:

Похожие инструкции для S2009BCDFCOSL

Бренды по названию

Популярные бренды