Arctic Cat S2009BCDFCOSL Скачать руководство пользователя

Страница: 16 / 88

GENERAL INFORMATION

At this point, the hours display will

begin to flash. Push the increment but-

ton to increase the hours; push the dec-

rement button to decrease the hours.

Pushing and holding a button will

accelerate the number display. When

desired hour number is displayed, push

the select button.

At this point, the minutes display will

begin to flash. Push the increment but-

ton to increase the minutes; push the

decrement button to decrease the min-

utes. Pushing and holding a button will

accelerate the number display. When

desired minute number is displayed,

push the select button.



NOTE: During clock setting if no

button (increment, decrement,
select) is pushed within a 5-sec-
ond time period, the clock-setting
mode will be exited with changes
saved.

The altimeter readout is based off baro-

metric pressure and may require cali-

bration as weather conditions change.

To calibrate the altimeter to an estab-

lished altitude with altimeter selected

on the display screen by pushing and

holding the select button for a mini-

mum of two seconds, the acronym

CAL will be displayed on the readout

screen for one second; then the altitude

value will flash. Push the increment

button to increase the displayed alti-

tude; push the decrement button to

decrease the displayed altitude. Push-

ing and holding a button will accelerate

the number display.



NOTE: If MPH has been selected

in the speed readout, the altitude
value will be displayed in feet. If
kph has been selected in the
speed readout, the altitude value
will be displayed in meters.

To reset the maximum altimeter read-

out with the maximum altimeter dis-

played, push and hold the select button

for a minimum of two seconds.

Service Icon

On electric start models, the icon

should illuminate each time the key is

turned to RUN or START, and it should

go out when the engine starts. If the

icon stays illuminated (on electric start

models) or it illuminates while the

engine is running, the system is receiv-

ing input that is outside of its estab-

lished parameters. If the system icon

illuminates indicating an error, take the

snowmobile to an authorized Arctic

Cat Snowmobile dealer for service. If

not under warranty, this service is at the

discretion and expense of the snowmo-

bile owner.

Coolant Temperature

Warning Icon

If the coolant temperature is at or

above the maximum running tempera-

ture, the coolant temperature warning

icon will flash a warning (alert). If the

coolant temperature is at or above the

maximum running temperature, the

coolant temperature warning icon will

cease flashing and will remain con-
stantly illuminated.

Crossfire/F-Series/M-Series/T500

Steady Flash
(Coolant
Temperature Icon)

Coolant Tempera-
ture Above 80° C
(176° F).

Constant On
(Coolant
Temperature Icon)

Coolant Tempera-
ture Above 93° C
(200° F).

Z1/TZ1

Steady Flash
(Coolant
Temperature Icon)

Coolant Tempera-
ture Above 110° C
(230° F).

Constant On
(Coolant
Temperature Icon)

Coolant Tempera-
ture Above 115° C
(239° F).

Содержание S2009BCDFCOSL

























































































Результаты поиска

Содержание S2009BCDFCOSL

Отзывы:

Похожие инструкции для S2009BCDFCOSL

Бренды по названию

Популярные бренды

Arctic Cat S2009BCDFCOSL, Руководство оператора

Результаты поиска

Содержание S2009BCDFCOSL

Отзывы:

Похожие инструкции для S2009BCDFCOSL

Бренды по названию

Популярные бренды