Arctic Cat S2009BCDFCOSL Скачать руководство пользователя | Manualshive

Страница: 45 / 88

background image

MAINTENANCE

41

In-Line Fuel Filter

(Carbureted Models)

Arctic Cat recommends that the in-line

fuel filter be checked weekly. The in-

line fuel filter is located just in front of

the fuel pump inlet fitting. The filter

must be clean to allow the fuel hose to

transmit the amount of gasoline

required.

If the in-line fuel filter is obstructed,

gasoline flow will be restricted; there-

fore, the filter must be replaced. To

remove and install the in-line fuel fil-

ter, use the following procedure:

1. Pinch off the fuel hose between the

gas tank and fuel filter.

2. Remove the clamps; then pry the

fuel hoses off the in-line fuel filter

and remove the filter.



NOTE: The in-line fuel filter must

be replaced if obstructed. Filters
are available from an authorized
Arctic Cat Snowmobile dealer.

3. Install the in-line fuel filter in the

fuel hose so the arrow on the filter

points toward the fuel pump. Make

sure the fuel hoses fit tightly on

the filter. If the existing fuel hose

does not fit tightly on the filter, cut

6 mm (1/4 in.) from the end of the

fuel hose; then install on the filter

and secure with the clamps.

728-272B

In-Line Fuel Filter

(1100 cc Models)

Arctic Cat recommends that the in-line

fuel filter be checked weekly and

replaced every 5000 miles. The in-line

fuel filter is located just inside the left-

side access panel. The filter must be

clean to allow the fuel hose to transmit

the amount of gasoline required.

If the in-line fuel filter is obstructed,

gasoline flow will be restricted; there-

fore, the filter must be replaced. To

remove and install the in-line fuel fil-

ter, use the following procedure:



NOTE: Before removing the fuel

filter, take note of the filter inlet
and outlet for installing purposes.

1. Open the left-side access panel;

then remove the fuel filter from

the bracket.

! WARNING

The fuel hoses must fit tightly on
the fuel filter. If the fuel hose length
doesn’t permit this procedure,
replace the fuel hose. Also, after
installing the fuel hoses on the fil-
ter, check to be sure that the fuel
hoses do not contact any hot or
rotating components.

! WARNING

Since the fuel supply hose may be
under pressure, always wear
safety glasses when removing the
fuel hoses.

! CAUTION

Since the fuel supply hose may be
under pressure, remove it slowly
to release the pressure. Place an
absorbent towel around the con-
nection to absorb the fuel.

«
...
43
44
45
46
47
...
»

Содержание S2009BCDFCOSL

























































































Отзывы:

Нет отзывов

Похожие инструкции для S2009BCDFCOSL

Бренд: Yamaha Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды