Arctic Cat S2009BCDFCOSL страница 17 Скачать руководство пользователя | Manualshive

Страница: 17 / 88

background image

GENERAL INFORMATION

13



NOTE: On the Z1/TZ1 models if

the coolant temperature icon is
constantly on, the engine will shut
off if vehicle speed is reduced to
1.5 kph (0.9 MPH) or slower.

Charging System

Warning Icon

(1100 cc Models)

The Charging System Warning Icon is

designed to warn the operator if the

battery charging system is not func-

tioning. The icon should illuminate

each time the key is turned to RUN or

START, and it should go out when the

engine starts. If the icon stays illumi-

nated or it illuminates while the engine

is running, the battery is not being

charged, and the snowmobile is run-

ning on battery reserve power only.

If the Charging System Warning Icon

illuminates, you should, as soon as pos-

sible, take the snowmobile to an autho-

rized Arctic Cat Snowmobile dealer for

service. If not under warranty, this ser-

vice is at the discretion and expense of

the snowmobile owner. The engine

WILL NOT RUN

without battery

power.

Low Oil Warning Icon

The Low Oil Warning Icon is designed

to alert the snowmobile operator when

the oil in the oil injection reservoir gets

below a prescribed level; however, it is

highly recommended that a visual veri-

fication of the oil level in the reservoir

be done prior to operating the snowmo-

bile. Once the Low Oil Warning Icon

illuminates during operation of the

snowmobile, the operator must periodi-

cally monitor the level of oil in the res-

ervoir and must fill the reservoir the

next time gasoline is added to the gas

tank. The “alert level” of the Low Oil

Warning Icon is approximately equal to

1 tankful of gasoline under normal

operating conditions.

Oil Pressure Warning

Icon (1100 cc Models)

The Oil Pressure Warning Icon indi-

cates engine oil pressure, not the oil

level; however, if the oil level is low, it

may affect oil pressure.

The icon should illuminate each time

the ignition switch is turned to RUN or

START, and it should go out when the

engine starts. If the icon illuminates

while the engine is running, oil pres-

sure has been lost and the engine will

automatically shut off.

If oil pressure is lost, use the following

procedure to check the oil level:

1. With the engine off, remove the

engine oil level stick and wipe it

clean. Without screwing it in, set

the stick back in the oil tank.

Remove it and observe the oil

level on the stick. If the oil level is

at or below the ADD mark on the

oil level stick, add only enough

recommended oil to raise the level

to the NORMAL range. DO NOT

overfill the reservoir with oil.

! CAUTION

At this point, take precautionary
measures such as changing to
loose snow terrain, shutting the
engine off (allowing the engine to
cool down), and checking coolant
level. If unable to either determine
or remedy the problem, take the
snowmobile to an authorized Arc-
tic Cat Snowmobile dealer for ser-
vice. If not under warranty, this
service is at the discretion and
expense of the snowmobile owner.

«
...
15
16
17
18
19
...
»

Содержание S2009BCDFCOSL

























































































Отзывы:

Нет отзывов

Похожие инструкции для S2009BCDFCOSL

Ski-Doo MX Z X 440 2007

Бренд: BRP Страницы: 30

Lynx Commander 800R E-TEC 2018

Бренд: BRP Страницы: 118

Lynx Rave 600RS 2020

Бренд: BRP Страницы: 188

Lynx Commander GT 1200 4-TEC Comfort

Бренд: BRP Страницы: 164

Lynx 69 Ranger 900 ACE

Бренд: BRP Страницы: 181

Lynx Radien ACE 2019 Series

Бренд: BRP Страницы: 237

LYNX DEEP SNOW SPORT 2023 Series

Бренд: BRP Страницы: 316

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды