background image

60

MAINTENANCE

3. If the distance between the bottom

of the wear strip and the inside sur-

face of the track is less than speci-

fied, loosen the adjusting bolts to

increase the slack in the track.

4. Check track alignment (see Track

Alignment sub-section).

5. When proper track tension is

obtained, tighten the adjusting bolt

jam nuts against the axle housings.

NOTE: Since track tension and

track alignment are interrelated,
always check both even if only one
adjustment seems necessary.

TRACK ALIGNMENT

Proper track alignment is obtained

when the rear idler wheels are equal

distance from the inner track drive

lugs. Excessive wear to the idler

wheels, drive lugs, and track will occur

if the track is improperly aligned. Arc-

tic Cat recommends that the track

alignment be checked once a week or

whenever the track tension is adjusted.

Checking Track 

Alignment

1. Remove excess ice and snow

buildup from the track, track drive

sprockets, and the inside of the

skid frame.

2. Position the tips of the skis against

a wall; then using a shielded safety

stand, raise the rear of the snow-

mobile off the floor making sure

the track is free to rotate.

3. Start the engine and accelerate

slightly. Use only enough throttle

to turn the track several revolu-

tions. SHUT ENGINE OFF.

NOTE: Allow the track to coast to

a stop. DO NOT apply the brake
because it could produce an inac-
curate alignment condition.

4. When the track stops rotating,

check the relationship of the rear

idler wheels and the inner track

drive lugs. If the rear idler wheels

are centered between the inner

track drive lugs, no adjustment is

necessary.

! WARNING

If jam nuts are not tightened prop-
erly, the adjusting bolts could
loosen causing the track to
become extremely loose and,
under some operating conditions,
allow the idler wheels to climb over
the track lugs forcing the track
against the tunnel causing the
track to “lock.” If a track “locks”
during operation, severe personal
injury could result.

! WARNING

Make sure the ignition key is in the
OFF position and the track is not
rotating before checking or adjust-
ing track alignment. Personal
injury could result if contact is
made with a rotating track.

! WARNING

The tips of the skis must be posi-
tioned against a wall or similar
object.

! WARNING

DO NOT stand behind the snowmo-
bile or near the rotating track.
NEVER run the track at high speed
when the track is suspended.

Содержание S2009BCDFCOSL

























































































Отзывы:

Похожие инструкции для S2009BCDFCOSL