Arctic Cat M4000 2016 страница 49 Скачать руководство пользователя

Страница: 49 / 60

Adjusting Rear Spring Pre-

Load

Proper adjustment of rear spring pre-load

is necessary to get the most desirable

ride. The chart is designed to help in set-

ting up rear spring pre-load; however,

riding style is the single greatest factor in

determining rear spring requirements.



NOTE: These cam position set-

tings are suggestions only. Personal
riding style will greatly influence
cam position settings. Spend time to
determine setting preferences.

Rear spring pre-load adjustment is accom-

plished by rotating the adjusting cams.

Position 3 provides the stiffest ride, and

position 1 is for the light driver or slow-

speed trail riding. Position 2 is for the

average operator under normal conditions.

Always rotate the cam from the lighter

position to the heavier position.

741-450A

To rotate an adjusting cam, use the spark

plug wrench from the tool kit. Rotate the

wrench until the cam is in the desired

position. To stiffen the ride, rotate the cam

so as to raise the spring end. Make the

appropriate adjustment on the other cam.

Adjusting Skid Frame Rear

Arm Shock Spring

Proper adjustment of rear arm shock

absorber spring pre-load is necessary to

get the most desirable ride.
The rear arm shock spring is adjustable

for the terrain conditions and driving

style and weight of the operator. The

spring adjuster nut has been set at the fac-

tory so the correct amount of threads are

exposed between the adjuster nut and the

threaded shock body as an initial setting.
Rear spring pre-load adjustment is

accomplished by loosening the adjuster

nut locking collar (B) from the adjuster

nut (A) and using the Spring Adjuster

Tool from the tool kit, rotating the

adjuster nut in whichever direction is

desired. Tighten the locking collar

against the adjuster nut.

0745-159

Lights

For the correct headlight bulb and/or tail-

light/brakelight LED, see the appropriate

specifications sheet.

Removing and Installing

Taillight/Brakelight

These models are equipped with an LED

taillight/brakelight. If the LED fails, it

must be replaced.

1. Disconnect the taillight harness con-

nector.

746-097B

Rider Weight (lb)

Cam Position

Up to 180

180-240

Over 240

CAUTION

Never force the adjustment cams
from the low position to the high
position. Cam damage may occur.

Содержание M4000 2016





























































Результаты поиска

Содержание M4000 2016

Отзывы:

Похожие инструкции для M4000 2016

Бренды по названию

Популярные бренды

Arctic Cat M4000 2016, Руководство оператора

Результаты поиска

Содержание M4000 2016

Отзывы:

Похожие инструкции для M4000 2016

Бренды по названию

Популярные бренды