Arctic Cat M4000 2016 Скачать руководство пользователя | Manualshive

Страница: 50 / 60

background image

46

2. Remove the two torx-head screws

securing the taillight to the bracket.

3. Connect the taillight harness connec-

tor; then secure the taillight to the

bracket with the two torx-head screws.

Removing/Installing

Headlight Bulb



NOTE: The bulb portion of headlight

is fragile. HANDLE WITH CARE. When
replacing the headlight bulb, the bulb
assembly must first be removed from
the housing. Do not touch the glass
portion of the bulb. If the glass is
touched, it must be cleaned with a dry
cloth before installing.

1. Disconnect the headlight harness

connector from the bulb; then

remove the rubber grommet from

the headlight housing.

2. Rotate the bulb retainer counter-

clockwise until it unlocks from the

housing; then remove the bulb.

0746-096

3. Install the bulb and retainer; then

rotate the retainer clockwise until it

properly locks in place.

4. Install the rubber grommet; then

connect the headlight harness con-

nector to the bulb.

5. Check headlight aim.

Adjusting Headlight Aim

The headlight can be adjusted for vertical

aim of the HIGH/LOW beam. The geo-

metric center of HIGH beam zone is to be

used for vertical aiming.

1. Position the snowmobile on a level

floor so the headlight is approxi-

mately 8 m (25 ft) from an aiming

surface (wall or similar surface).



NOTE: There should be an “aver-

age” operating load on the snowmo-
bile when adjusting headlight aim.

2. Measure the distance from the floor

to midpoint of the headlight.

3. Using the measurement obtained in

step 2, make a horizontal mark on

the aiming surface.

4. Make a vertical mark which inter-

sects the horizontal mark on the aim-

ing surface directly in front of the

headlight.

5. Engage the brake lever lock and start

the engine. Move the headlight dim-

mer switch to the HIGH beam posi-

tion. DO NOT USE LOW BEAM.

6. Observe the headlight beam aim.

Proper aim is when the most intense

beam is centered on the vertical mark

5 cm (2 in.) below the horizontal

mark on the aiming surface.

0745-813

7. Adjust the headlight using the adjust-

ing screw on the backside of the head-

light using a 4 mm swivel socket and

long extension until correct aim is

obtained. Shut the engine off; then

disengage the brake lever lock.

! WARNING

Do not operate the snowmobile
unless headlight beam is adjusted
properly. An incorrectly adjusted
beam will not provide the operator
the optimum amount of light.

«
...
48
49
50
51
52
...
»

Содержание M4000 2016





























































Отзывы:

Нет отзывов

Похожие инструкции для M4000 2016

Бренд: Yamaha Страницы: 209

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды