background image

28

The longevity and safety of the snowmo-

bile can be increased by making periodic

checks of the items in the preceding

checklist.
If, at any time, abnormal noises, vibra-

tions, or improper working conditions of

any component of this snowmobile are

detected, DO NOT OPERATE THE

SNOWMOBILE. Take the snowmobile

to an authorized Arctic Cat Snowmobile

dealer for inspection and adjustment or

repair. If not under warranty, this service

is at the discretion and expense of the

snowmobile owner.
The snowmobile should be taken to an

authorized Arctic Cat Snowmobile dealer

at the end of each snowmobiling season

for general inspection and for off-season

storage servicing. This inspection and

servicing is at the expense of the snow-

mobile owner.

Fuel System

In-Line Fuel Filter (6000)

Arctic Cat recommends that the in-line

fuel filter be replaced every 5000 miles.

The filter must be clean to allow the fuel

hose to transmit the amount of gasoline

required. 
If the in-line fuel filter is obstructed, gas-

oline flow will be restricted; therefore,

the filter must be replaced. To remove

and install the in-line fuel filter, use the

following procedure:

NOTE: Before removing the fuel fil-

ter, take note that the filter is direc-
tional and the arrow should be
directed towards the engine.

NOTE: The fuel filter is located

above the recoil. To access the filter,
the access panels and hood need to
be removed.

XM183A

1. Remove the hose clamps and discard;

then slowly remove the fuel hoses

from the fuel filter. Dispose of the

excess fuel from the filter properly.

2. Inspect the fuel hoses thoroughly for

any signs of cracking, cuts, or wear

points.

3. Place the new hose clamps on the

fuel hoses; then with the fuel pump

inlet and outlet noted, connect the

fuel hoses to the fuel filter. Secure

with the hose clamps.

NOTE: After completing the

changing of the fuel filter and the
engine is started for the first time,
inspect the filter area for any signs
of leaks.

Gasoline Additives

Fuel de-icer can be used for all models.

On the 8000, periodic use of the injector

cleaner is recommended especially in the

last tank of gasoline before storage. Arc-

tic Cat Fuel Stabilizer (p/n 0436-907)

should also be added to the last tank of

gasoline before storage.

Fuel Pickup Valves

If ever there is a restricted fuel flow and a

pickup valve is suspected, take the snow-

mobile to an authorized Arctic Cat Snow-

mobile dealer for this service. If not under

warranty, this service is at the discretion

and expense of the snowmobile owner.

! WARNING

Whenever any maintenance or
inspection is made on the fuel sys-
tem in which there may be fuel leak-
age, there should be no welding,
smoking, open flames, etc., in the
area.

! WARNING

Since the fuel supply hose may be
under pressure, always wear safety
glasses; then remove the hose slowly
to release the pressure. Place an
absorbent towel around the connec-
tion to absorb the fuel. 

CAUTION

Make sure the fuel filter is properly
seated into the holder.

Содержание M4000 2016





























































Отзывы:

Похожие инструкции для M4000 2016