Arctic Cat bearcat 2000l bearcat 3000 Скачать руководство пользователя | Manualshive

Страница: 59 / 72

background image

55

To move the spring slide, remove the nut

on the backside of the spring slide cap

screw; then carefully remove the spring

slide and cap screw to the desired loca-

tion. Install the nut and tighten to 25 ft-lb.

Articulating Skid Frame

(7000)

The rear articulating portion of the skid

frame has two skid frame knobs which

allows the skid frame to be locked or

allows it to articulate.
To allow the rear of the skid frame to

articulate, pull out the knobs on the left-

side of the skid frame and rotate the knob

and adjustment block up and forward

until it locks into the upper mounting

hole.

XM316A

XM315A

Overload Springs

Some models have overload springs built

into the rear suspension. When either car-

rying a heavy load or riding 2-up, the

overload springs should be engaged by

rotating the spring tension blocks to the

UP position. The spring tension blocks

lock in an over-center position when

engaged.



NOTE: Arctic Cat recommends

that the overload springs be
engaged whenever a load on the
snowmobile (operator/passenger/
cargo) exceeds 136 kg (300 lb).

To either engage or disengage the spring

tension blocks, use a spark plug socket

and a screwdriver to adjust the spring

block to the desired position. Make sure

both spring blocks are in the same posi-

tion (either engaged or disengaged).

744-457A

Lights

For the correct headlight bulb and/or tail-

light/brakelight LED, see the specifica-

tions sheet.

Removing and Installing

Taillight/Brakelight

Lynx

These models are equipped with an LED

taillight/brakelight. If the LED fails, it

must be replaced. To remove and install

the LED, use the following procedure.

CAUTION

There are weight limitations for these
snowmobiles. If additional cargo is
being added, maximum weight on the
snowmobile (operator/passenger/
cargo) should not exceed the maxi-
mum limitation set for each snowmo-
bile. See chart for details. Also, the
overload springs should be engaged.

Maximum Weight Limitations

Bearcat 2000/

3000 LT

170 kg

375 lb

Bearcat 2000 XT/

XTE

272 kg

600 lb

Bearcat 7000/

Pantera XT LTD

272 kg

600 lb

Lynx 2000 LT

170 kg

375 lb

«
...
57
58
59
60
61
...
»

Содержание bearcat 2000l bearcat 3000









































































Отзывы:

Нет отзывов

Похожие инструкции для bearcat 2000l bearcat 3000

Бренд: Hammerhead Страницы: 11

Бренд: Hammerhead Страницы: 70

Бренд: Lynx Страницы: 75

Бренд: Taylor-Dunn Страницы: 144

Бренд: Roketa Страницы: 15

Бренд: Whirlwind Страницы: 7

Бренд: Dometic Страницы: 96

Бренд: Har-Tru Страницы: 12

Ranger 500 2x4 2007

Бренд: Polaris Страницы: 345

Бренд: Rollplay Страницы: 28

FEBER quad KRIPTON

Бренд: Famosa Страницы: 4

Бренд: Yamaha Страницы: 468

Бренд: CF MOTO Страницы: 272

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды