Arctic Cat bearcat 2000l bearcat 3000 Скачать руководство пользователя

Страница: 60 / 72



NOTE: To access the harness con-

nector and the two self-tapping
screws securing the taillight to the
snowflap, compress the two flanged
tabs (located on the under-side of
the tunnel) and carefully pry up on
the front of the taillight/snowflap.

0744-462

1. Disconnect the taillight harness con-

nector.

2. Remove the two self-tapping screws

securing the taillight to the snowflap.

3. Secure the taillight to the snowflap

with the two self-tapping screws;

then connect the taillight connector.

4. Secure the front of the snowflap to

the tunnel by carefully tapping the

snowflap until the two flanged tabs

snap into place.

Bearcat 2000 LT/Lynx LT

1. Remove the torx-head cap screws

securing the taillight access panel.

742-467A

2. Disconnect the harness connector

and remove housing.

3. Push in on the socket and rotate it

counterclockwise to remove it from

the housing.

4. Remove the old bulb by pulling it

straight out of the socket.

5. Install the new bulb in the socket by

pushing it straight in.

6. Push the socket into the housing and

rotate it clockwise to lock into place.

7. Connect the harness connector.
8. Secure the access panel with the

torx-head cap screws.

Bearcat 2000 XT/XTE

1. Remove the four pins securing the

rear seat to the seat/Speedrack mount.

743-329A

2. Lift on the back of the rear seat and

move rearward to remove it from the

mount.

3. Compress the latch on the right side

of the front seat and lift the front seat

away; then disconnect the taillight

harness connector.

743-444A

4. Loosen (but do not remove) the

three right-side seat/Speedrack

mount cap screws.

5. Carefully route the harness connec-

tor through the hole in the storage

compartment panel; then remove the

harness from beneath the seat/Spee-

drack mount.

6. Remove the two self-tapping screws

securing the taillight to the bumper;

then route the harness out of the

bumper and remove the taillight.

Содержание bearcat 2000l bearcat 3000









































































Результаты поиска

Содержание bearcat 2000l bearcat 3000

Отзывы:

Похожие инструкции для bearcat 2000l bearcat 3000

Бренды по названию

Популярные бренды

Arctic Cat bearcat 2000l bearcat 3000, Руководство оператора

Результаты поиска

Содержание bearcat 2000l bearcat 3000

Отзывы:

Похожие инструкции для bearcat 2000l bearcat 3000

Бренды по названию

Популярные бренды