Arctic Cat bearcat 2000l bearcat 3000 Скачать руководство пользователя

Страница: 53 / 72

0749-025

3. When the sheaves are fully apart,

pull up on drive belt and roll belt

over stationary sheave until it is free

of the driven clutch.

4. When the belt is free of driven

clutch, remove the belt from the

drive clutch.

Installing - 7000

1. Place the belt (so the part number

can be read) between the sheaves of

the drive clutch.

2. With the sheaves fully apart, roll the

belt over the stationary sheave.

3. With the drive belt properly posi-

tioned in the drive clutch and driven

clutch, turn the belt tool counter-

clockwise and roll the belt back and

forth to allow the driven clutch

sheaves to fully close.

4. After the belt is installed properly,

install the left-side access panel and

close the hood.

5. Release the brake lever lock.

Removing - 2000/3000

1. Turn ignition key to the OFF posi-

tion and wait for all moving parts to

stop.

2. Set the brake lever lock.
3. Open the left-side access panel.
4. Remove the cap screw, lock washer,

washer, and sheave adjuster from the

end of the driven clutch; then

remove the sheave adjuster from the

cap screw.

0743-395



NOTE: Each time the driven clutch

cap screw is removed, the hole in the
driven shaft should be cleaned free
of any Loctite residue.



NOTE: Verify the shims and O-ring

are not removed from the adjuster.

5. Remove the lock washer and flat

washer from the cap screw and

reverse the sheave adjuster.

6. Install the cap screw into the driven

clutch; then tighten the cap screw

until the movable sheave opens far

enough to allow the belt to be

removed.

7. Remove the drive belt from the

driven clutch first; then from the

drive clutch.



NOTE: Before installing the drive

belt, use a suitable cleaning solvent
to thoroughly clean the sheaves.

Installing - 2000/3000

1. Place the drive belt (so the part num-

ber can be read and the arrows are

facing the front of the snowmobile)

between the sheaves of the drive

clutch first; then between the

sheaves of the driven clutch.

2. Install the cap screw, lock washer,

washer, and sheave adjuster back into

the driven clutch. Tighten the cap

screw (apply a few drops of blue Loc-

tite #243 to the threads) to 20 ft-lb.

CAUTION

Before securing the driven clutch, be
sure the rollers are up against the
torque bracket or damage to the
back-side cams may occur.

Содержание bearcat 2000l bearcat 3000









































































Результаты поиска

Содержание bearcat 2000l bearcat 3000

Отзывы:

Похожие инструкции для bearcat 2000l bearcat 3000

Бренды по названию

Популярные бренды

Arctic Cat bearcat 2000l bearcat 3000, Руководство оператора

Результаты поиска

Содержание bearcat 2000l bearcat 3000

Отзывы:

Похожие инструкции для bearcat 2000l bearcat 3000

Бренды по названию

Популярные бренды