manualshive.com logo in svg

Arctic Cat bearcat 2000l bearcat 3000, Руководство оператора

Поделиться
Скачать
Arctic Cat bearcat 2000l bearcat 3000 Скачать руководство пользователя страница 24

20

NOTE: If additional cargo is being

added, maximum weight on the snow-
mobile (operator/passenger/cargo)
should not exceed the maximum lim-
itation set for each snowmobile. See
the chart in the Suspension - Over-
load Springs sub-section in the Main-
tenance section for details. Also, the
overload springs should be engaged.

To remove the rear seat, rotate the seat

latch either clockwise or counterclock-

wise and hold it in that position; then lift

and remove the seat from the tunnel.

742-593B

To install the seat, use the following pro-

cedure:

1. Place the seat into position on the

tunnel.

2. Rotate the seat latch either clock-

wise or counterclockwise and hold it

in that position; then slide the seat

forward, allow it to settle into posi-

tion, and release the latch to lock the

seat securely.

Bearcat 7000 XT

To remove the rear seat, lift up the lever

on the rear of the seat and hold it in that

position; then lift and remove the seat.

0749-032

To install the rear seat, position the front

of the seat base tabs under the loops in

the seat frame; then press down and

secure.

Pantera 7000 XT LTD

To remove the rear seat, lift up the lever

on the rear of the seat and hold it in that

position; then lift and remove the seat.

0749-032

To install the rear seat, position the front

of the seat base tabs into the two slots in

the seat frame; then press down and

secure.

Removable Light Bar 

(Bearcat XT GS)

This snowmobile is equipped with a

removable light bar. To remove and

install, use the following procedure.

! WARNING

Make sure the rear seat is securely
locked in place before carrying a pas-
senger or personal injury may result.

! WARNING

Make sure the rear seat is securely
locked in place before carrying a pas-
senger or personal injury may result.

! WARNING

Make sure the rear seat is securely
locked in place before carrying a pas-
senger or personal injury may result.

Содержание bearcat 2000l bearcat 3000









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды