Arctic Cat bearcat 2000l bearcat 3000 Скачать руководство пользователя

Страница: 20 / 72

9. Start the snowmobile with the dead

battery and allow it to run for several

minutes before disconnecting the

jumper cables.

10. Remove the jumper cables in oppo-

site order of hook-up (4, 3, 2, 1). Be

careful not to short cables against

bare metal.



NOTE: Have the battery and elec-

trical system checked prior to oper-
ating the snowmobile again.

Drive Clutch and Driven

Clutch

The drive clutch and driven clutch do not

require lubrication; therefore, no special

maintenance is required by the snowmo-

bile owner except for periodical cleaning

(see the Periodic Maintenance Checklist

in the Maintenance section).
However, the drive clutch and driven

clutch should be disassembled, cleaned,

and inspected by an authorized Arctic

Cat Snowmobile dealer after every 800

miles of operation or at the end of the

snowmobiling season whichever occurs

first. This service is at the discretion and

expense of the snowmobile owner.
When operating the snowmobile at high

altitudes, it may be necessary to change

certain component parts of the drive

clutch and/or the driven clutch. See an

authorized Arctic Cat Snowmobile dealer

for further information.

Drive Clutch/Driven

Clutch Alignment

The offset between the drive clutch and

driven clutch are set at the factory. Nor-

mally, no adjustment is necessary as long as

neither the drive clutch nor the driven clutch

is removed or disassembled. However, if

premature drive belt wear is experienced or

if the drive belt turns over, the drive clutch/

driven clutch alignment must be checked.

Take the snowmobile to an authorized Arc-

tic Cat Snowmobile dealer for this service.

If not under warranty, this service is at the

discretion and expense of the snowmobile

owner.

Fuel Pump

The fuel pump is designed to provide ade-

quate amount of gas to the injectors at all

throttle settings. If a fuel delivery problem is

suspected, take the snowmobile to an autho-

rized Arctic Cat Snowmobile dealer. If not

under warranty, this service is at the discre-

tion and expense of the snowmobile owner.

Shock Absorbers

Each shock absorber should be visibly

checked weekly for fluid leakage, cracks or

breaks in the lower case, or a bent plunger.

If any one of these conditions is detected,

replacement is necessary. Take the snow-

mobile to an authorized Arctic Cat Snow-

mobile dealer for this service. If not under

warranty, this service is at the discretion and

expense of the snowmobile owner.

Standard-Lug Track

Accelerated wear strip wear caused by

operating on ice or hard-packed snow

conditions is NOT covered under Arctic

Cat Inc. warranty policy.

Track Studs



NOTE: Stud or hooker plate installa-

tion will void track and tunnel warranty.



NOTE: Arctic Cat does not recom-

mend studding a track with a 1.5
inch lug or greater.

CAUTION

DO NOT attempt to service the drive
clutch and driven clutch. The drive
clutch and driven clutch must be ser-
viced by an authorized Arctic Cat
Snowmobile dealer only.

Содержание bearcat 2000l bearcat 3000









































































Результаты поиска

Содержание bearcat 2000l bearcat 3000

Отзывы:

Похожие инструкции для bearcat 2000l bearcat 3000

Бренды по названию

Популярные бренды

Arctic Cat bearcat 2000l bearcat 3000, Руководство оператора

Результаты поиска

Содержание bearcat 2000l bearcat 3000

Отзывы:

Похожие инструкции для bearcat 2000l bearcat 3000

Бренды по названию

Популярные бренды