Arctic Cat bearcat 2000l bearcat 3000 страница 13 Скачать руководство пользователя

Страница: 13 / 72

E. Service Icon

On electric start models, the icon should

illuminate each time the key is turned to

RUN or START, and it should go out

when the engine starts. If the icon stays

illuminated (on electric start models) or it

illuminates while the engine is running,

the system is receiving input that is out-

side of its established parameters. If the

icon illuminates indicating an error, take

the snowmobile to an authorized Arctic

Cat Snowmobile dealer for service. If not

under warranty, this service is at the dis-

cretion and expense of the snowmobile

owner.

F. High Beam Indicator

The indicator is on whenever the high

beam mode is selected by the headlight

switch.

Standard Gauge (3000/

7000)

XM248A

1. Left Button - Shifts top display

through speedometer, RPM, and

clock.

2. Middle Button - Shifts middle dis-

play through speedometer, RPM,

clock, odometer, trip 1, trip 2, and

engine hours.

3. Right Button - Shifts bottom display

through coolant temperature, bat-

tery voltage, and fuel level.

4. Speedometer/Tachometer Display -

Indicates approximate vehicle speed

in MPH or KM/H when speedome-

ter function is selected, RPM when

tachometer function is selected.

Press the Left Button to change

which parameter is being displayed.

With speedometer selected, press

and hold the Left Button to shift

between standard (MPH/miles/Fahr-

enheit) and metric (km/h/kilometers/

Celsius).

5. Engine Hour Meter/Odometer/Trip

Meter/Speedometer/Tachometer/

Clock Display - Displays engine

hours, odometer, trip meter, speed-

ometer, tachometer, or clock. Press

the Middle Button to change which

parameter is being displayed. The

Engine Hour Meter and Odometer

cannot be reset. To reset the trip

meter, select the Trip Meter; then

press and hold the Middle Button

until the trip meter display reads 0.
With the clock mode selected, press

and hold the Left Button to set the

clock. The option of selecting the

12-hour or 24-hour clock is avail-

able; press the Left Button to alter-

nate between the two modes. Next,

press the Middle Button to set the

clock. Press the Left or Right to set

the hours; then press the Middle

Button to set the minutes. Press the

Left or Right Button to set the min-

utes. When the proper time has been

set, press the Middle Button to

return to the main gauge display.

6. Coolant Temperature/Battery Volt-

age/Fuel Level Display - Displays

coolant temperature, battery voltage,

and fuel quantity. Press the Right

Button to change which parameter is

being displayed. Press and hold the

Right Button to see the actual values

associated with the mode selected.

7. Gear Position Indicator - Indicates

what gear the transmission is in.

8. Coolant Temperature Indicator -

When the snowmobile is started, this

indicator will flash and LOW TEMP

will be displayed until the engine

reaches operating temperature.

Содержание bearcat 2000l bearcat 3000









































































Результаты поиска

Содержание bearcat 2000l bearcat 3000

Отзывы:

Похожие инструкции для bearcat 2000l bearcat 3000

Бренды по названию

Популярные бренды

Arctic Cat bearcat 2000l bearcat 3000, Руководство оператора

Результаты поиска

Содержание bearcat 2000l bearcat 3000

Отзывы:

Похожие инструкции для bearcat 2000l bearcat 3000

Бренды по названию

Популярные бренды