manualshive.com logo in svg

Arctic Cat bearcat 2000l bearcat 3000, Руководство оператора

Поделиться
Скачать
Arctic Cat bearcat 2000l bearcat 3000 Скачать руководство пользователя страница 63

59

5. Check headlight aim.

Adjusting Headlight Aim
2000

The headlight can be adjusted for vertical

aim of the HIGH/LOW beam. The geo-

metric center of HIGH beam zone is to be

used for vertical aiming.

1. Position the snowmobile on a level

floor so the headlight is approxi-

mately 8 m (25 ft) from an aiming

surface (wall or similar surface).

NOTE: There should be an “aver-

age” operating load on the snowmo-
bile when adjusting headlight aim.

2. Measure the distance from the floor

to midpoint of the headlight.

3. Using the measurement obtained in

step 2, make a horizontal mark on

the aiming surface.

4. Make a vertical mark which intersects

the horizontal mark on the aiming sur-

face directly in front of the headlight.

5. Engage the brake lever lock and start

the engine. Move the headlight dim-

mer switch to the HIGH beam posi-

tion. DO NOT USE LOW BEAM.

6. Observe the headlight beam aim.

Proper aim is when the most intense

beam is centered on the vertical mark

5 cm (2 in.) below the horizontal

mark on the aiming surface.

0741-448

7. Adjust the headlight using the

adjustment knobs until correct aim is

obtained. Shut the engine off; then

disengage the brake lever lock.

3000/7000

The headlight can be adjusted for vertical

aim of the HIGH/LOW beam. The geo-

metric center of HIGH beam zone is to be

used for vertical aiming.

1. Position the snowmobile on a level

floor so the headlight is approxi-

mately 8 m (25 ft) from an aiming

surface (wall or similar surface).

NOTE: There should be an “aver-

age” operating load on the snowmo-
bile when adjusting headlight aim.

2. Measure the distance from the floor

to midpoint of the headlight.

3. Using the measurement obtained in

step 2, make a horizontal mark on

the aiming surface.

4. Make a vertical mark which intersects

the horizontal mark on the aiming sur-

face directly in front of the headlight.

5. Engage the brake lever lock and start

the engine. Move the headlight dimmer

switch to the HIGH beam position. DO

NOT USE LOW BEAM.

6. Observe the headlight beam aim.

Proper aim is when the most intense

beam is centered on the vertical mark 5

cm (2 in.) below the horizontal mark

on the aiming surface.

SNO-520A

7. Adjust the headlight using the adjust-

ing screw on the backside of the head-

light using a 4 mm swivel socket and

long extension until correct aim is

obtained. Shut the engine off; then dis-

engage the brake lever lock.

! WARNING

Do not operate the snowmobile
unless headlight beam is adjusted
properly. An incorrectly adjusted
beam will not provide the operator
the optimum amount of light.

Содержание bearcat 2000l bearcat 3000









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды