ARB 3917140 Скачать руководство пользователя страница 1

 

24-04-13 

Page 1 of 12 

 

3786417

 

 

 

 

 

 

 

If you have any queries regarding the installation of this product please contact the distributor from whom it was purchased, or alternatively the ARB office in your state. 

Head Office – ARB Corporation Ltd VIC: 42-44 Garden Street, Kilsyth, Victoria, 3137 Tel: (03) 9761 6622 Fax: (03) 9761 6807 

WA:

(08) 9244 3553  

NSW:

 (02) 9821 3633  

ACT:

 (02) 6280 7475  

SA:

 (08) 8244 5001  

QLD:

 (07) 3872 3872  

NT:

 (08) 8947 2262  

TAS:

 (03) 6331 4190

 

 

ARB WINCH/NON WINCH BUMPER TO SUIT 08/2004 

ONWARDS NISSAN GU PATROL 

 

PRODUCT NO:  

3917140 

 

 

 

5100050  Top Tube Kit 
5100160  Buffer Kit – With hole (required when fitting Top Tube) 
5100170  Buffer Kit – With no hole 
 

FITTING KIT NO:   6172355 

 

WARNING 

FOR VEHICLES EQUIPPED WITH SRS AIRBAG 

WHEN INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS, THE FRONT 

PROTECTION BAR DOES NOT AFFECT OPERATION OF THE SRS AIRBAG. 

 

TAKE NOTE OF THE FOLLOWING: 

 

 

THIS PRODUCT MUST BE INSTALLED EXACTLY AS PER THESE INSTRUCTIONS 
USING ONLY THE HARDWARE SUPPLIED. 

 

 

IN THE EVENT OF DAMAGE TO ANY BULL BAR COMPONENT, CONTACT YOUR 
NEAREST AUTHORISED ARB STOCKIST. REPAIRS OR MODIFICATIONS TO THE 
IMPACT ABSORPTION SYSTEM MUST NOT BE ATTEMPTED. 

 

DO NOT USE THIS PRODUCT FOR ANY VEHICLE MAKE OR MODEL, OTHER THAN 
THOSE SPECIFIED BY ARB. 

 

 

DO NOT REMOVE LABELS FROM THIS BULL BAR. 

 

 

OPTIONAL LIGHT SETS TO SUIT THIS PRODUCT: 

- ARB 6821201 Fog Light Kit Suit 3163015 

- Up to IPF 900 SERIES FOG OR DRIVING LIGHT SETS 

 
IMPORTANT 

 

This winch bumper is suitable only for Warn winches up to 9500lb.

 

 

 

 

Содержание 3917140













Отзывы: