background image

 

4

Table of contents

 

 

Scope of delivery 

 

 

3 Safety 

warnings 

 

5  

Introduction reverse osmosis 

 

 

6 - 7 

Operating instructions 

 

8 - 9 

Shutdown, fresh water flush. 

 

10 - 11 

Long term preservation (mothballing), antifreeze 

 

12 Membrane 

cleaning 

 

 

13 Memos 

 

14 – 15 

Flow diagram 

 

16 - 20 

Installation 

 

21 – 23 

Electrical connection 

 

 

24 

Important: Inspection and maintenance 

 

25 

Change of membranes 

 

 

26 – 27 

Troubleshooting

 

 

28 – 31 

Clamping torques / Spare parts

 

 

 

32 – 36 

Specification / dimensions  

 

 
 
Recommendation for using your Aquatec reverse osmosis system. 
 
Daily use is preferable to a one-time weekly use. 
 
The system produces water with a neutral taste and very good quality. 

Important:

 The drinking water must be bottled from the test outlet of the system during operation, 

ideally after filling the on-board water tank. Only fill the required amount until the next operation of the 
plant. Clean the drinking water bottle regularly. 
 
If the product water from the on-board water tank is used as drinking water, follow-up-treatment is 
recommended. No further treatment is usually necessary as service water. 
 
 

Содержание Watermaker AC 110







































Отзывы: