Apxalarm APX32EN, Руководство по программированию

Страница: 20 / 24

- 20 -
POWERLINE CARRIER DEVICES WORKSHEET FOR
✻
✻ ✻
✻
80, and
✻
✻ ✻
✻
81.
Applicable only if Powerline Carrier Devices are to be used, or chime-by-zone feature is used.
UL
Powerline Carrier Devices have not been evaluated by UL.
✱
80 OUTPUT DEVICES
Fill in the required data on the worksheet on below and follow the programming procedure in the Installation
Instructions as you enter the data during the displays and prompts that appear in sequence.
Note : Field
✱
25 must be programmed with a House Code.
S T A R T
either or both
S T O P
either or both
DEVICE
NUMBER
ACTION
(aa)
EVENT ZONE
TYPE (et) LIST (zl)
ZONE TYPE
SYS OPERATION (zt)
RESTORE
ZONE LIST (zl)
ZONE TYPE/
SYS OPERATION (zt)
P.L.C.D.*† 01
P.L.C.D.*† 02
P.L.C.D.* † 03
P.L.C.D.* 04
P.L.C.D.* † 05
P.L.C.D.*† 06
SYS. P.L.C.D.*† 07
SYS. P.L.C.D.*† 08 [2] [33] [36]
E-mail Event Trigger 09
E-mail Event Trigger 10
E-mail Event Trigger 11
E-mail Event Trigger 12
E-mail Event Trigger 13
E-mail Event Trigger 14
E-mail Event Trigger 15
E-mail Event Trigger 16 [2] [33] [36]
* P.L.C.D. = Powerline Carrier Device (X10).
Where: A = DEVICE ACTION
0 = No Response; 1 = Close for 2 sec; 2 = Close and stay closed; 3 = Pulse on and off.
ET = EVENT TYPE
0 = Not used; 1 = Alarm; 2 = Fault; 3 = Trouble.
Z L = ZONE LIST 1, 2, or 3 (from Field
✱
81) or 0 = Not Used.
"START" ZONE LIST: Upon alarm, fault, or trouble of ANY zone on this list, device action will START.
"STOP"
RESTORE of ZONE LIST: Upon restore of ALL zones on this list, device action will STOP.
It need not be same list as used for START.
Note: Do not assign zones with types 20, 21, or 22 to a zone list.
3
ZT = ZONE TYPE/
SYSTEM OPERATION
Choices for Zone Types are:
00 = Not Used 07 = 24 Hour Audible
01 = Entry/Exit#1 08 = 24 Hour Aux
02 = Entry/Exit#2 09 = Fire Zone without Verification
03 = Perimeter 10 = Interior with Delay
04 = Interior Follower 14 = Carbon Monoxide
05 = Trouble Day/Alarm Night 24= Silent Burglary
06 = 24 Hour Silent
Choices for System Operation are:
20 = Arming–Stay 33 = Any Alarm* 42 = System Battery Low
21 = Arming–Away 36 = At Bell Timeout** 43 = Communication Failure
22 = Disarming (Code + OFF) 38 = Chime 52 = Kissoff
31 = End of Exit Time 39 = Any Fire Alarm 58 = Duress
32 = Start of Entry Time 40 = Bypassing
* Except ZT=08, 09, 14 or 16.
** Or at Disarming, whichever occurs earlier.
Note: In normal operation mode:
For Devices 1-6: For Devices 7 and 8: N = device (unit) number
Fu Lights On + N Code + Fu 4 + N (Entry starts Device N)
Fu Lights Off + N Code + Fu 7 + N (Entry stops Device N)
Note : Any zone in "ZT" going into alarm, fault, or trouble will activate device with the
exception of 01, 02 when the system is in alarm. Any zone that restores will
stop device action.