APRILIA ETX 150 Скачать руководство пользователя

Страница: 67 / 170

•

Remove the desmodromic (4)

Controllo alberi

Check transmission gears for signs of pitting and wear and replace damaged gears if necessary.

Check the gear fitting teeth for cracks, damage and wear and replace those damaged if necessary.

Check the transmission gears movement and, if it is not regular, replace the damaged part.

Checking the desmodromic drum

•

Check the wear of the grooves (1) and

of the contact surfaces with the bear-

ings (2).

•

In case of abnormal wear, replace the

desmodromic and check the bearings

in the crankcase

Checking the forks

Check the transmission fork cam roller (1) and the

gear fork tooth (2) for damage, distortion and wear.

Replace the transmission fork if necessary.

ETX - STX 150

Engine

ENG - 67

Содержание ETX 150











































































































































































Результаты поиска

Содержание ETX 150

Отзывы:

Похожие инструкции для ETX 150

Бренды по названию

Популярные бренды

APRILIA ETX 150, Руководство по обслуживанию станции

Результаты поиска

Содержание ETX 150

Отзывы:

Похожие инструкции для ETX 150

Бренды по названию

Популярные бренды