APRILIA ETX 150 Скачать руководство пользователя

Страница: 43 / 170

The connectors in the list are circled in the different pictures. The listed connectors are con-

sidered more critical than the others because their disconnection could cause the vehicle to

stop or malfunction. Obviously, the correct connection of the other connectors is also important

and essential for proper vehicle operation.

It is also important and essential that the instructions regarding the routing and fixing of the cable har-

ness in the various areas are followed meticulously in order to guarantee functionality and reliability.

Front side

TABLE A: FRONT HEADLIGHT ASSEMBLY

1. Front lights cable harness connector

2. Front light cable harness

3. Front main cable harness

4. Left front turn indicator connectors

5. Right front turn indicator connectors

TABLE A1: FRONT HEADLIGHT ASSEMBLY

•

Fix the front cable harness to the sup-

port frame with a clamp (6)

TABLE A2: FRONT HEADLIGHT ASSEMBLY

3. Front main cable harness

7. Front main cable harness connector

•

Pass the front cable harness through

the cable grommet (8)

ETX - STX 150

Electrical system

ELE SYS - 43

Содержание ETX 150











































































































































































Результаты поиска

Содержание ETX 150

Отзывы:

Похожие инструкции для ETX 150

Бренды по названию

Популярные бренды

APRILIA ETX 150, Руководство по обслуживанию станции

Результаты поиска

Содержание ETX 150

Отзывы:

Похожие инструкции для ETX 150

Бренды по названию

Популярные бренды