APRILIA ETX 150 Скачать руководство пользователя | Manualshive

Страница: 36 / 170

background image

Otherwise, top-up.

THE SYSTEM MUST ONLY BE TOPPED UP WITH DOT4
TYPE BRAKE FLUID.

BRAKE FLUID IS HIGHLY CORROSIVE - AVOID CONTACT
WITH PAINTWORK. IN THE EVENT OF SPILLAGE ON
PAINTED PARTS, RINSE IMMEDIATELY WITH WATER.

WARNING

THE FLUID IN THE BRAKING CIRCUIT IS HYGROSCOPIC,
THAT IS, IT ABSORBS MOISTURE FROM THE SUR-
ROUNDING AIR. IF THE MOISTURE CONTENT IN THE
BRAKE FLUID EXCEEDS A CERTAIN VALUE, WATER VA-
POUR BUBBLES MAY FORM IN THE CIRCUIT, OR THE
PUMP AND CALLIPERS MAY SEIZE, CAUSING THE
BRAKES THEMSELVES TO SEIZE. NEVER USE BRAKE
LIQUID IN OPEN OR PARTIALLY USED CONTAINERS.

Top-up

RISK OF BRAKE FLUID SPILLAGE. DO NOT USE THE BRAKE LEVER WHILE THE BRAKE FLUID
TANK CAP IS LOOSENED OR REMOVED.

CAUTION

AVOID PROLONGED EXPOSURE OF THE BRAKE FLUID TO THE AIR. THE BRAKE FLUID IS
HYGROSCOPIC AND ABSORBS MOISTURE WHEN IS IN CONTACT WITH THE AIR. LEAVE THE
BRAKE FLUID RESERVOIR OPEN ONLY FOR THE TIME NEEDED TO COMPLETE THE REFILL
PROCEDURE.

TO AVOID BRAKE FLUID SPILLING OUT DURING THE PROCEDURE, MAINTAIN THE FLUID IN
THE TANK PARALLEL TO THE EDGES OF THE TANK (HORIZONTAL). DO NOT ADD ADDITIVES
OR OTHER SUBSTANCES TO THE FLUID. IF YOU USE A FUNNEL OR ANOTHER IMPLEMENT,
MAKE SURE THAT THEY ARE PERFECTLY CLEAN.

THE BRAKE FLUID IS HIGHLY CORROSIVE, AVOID CONTACT WITH SKIN

AND EYES AND

PARTS OF THE MOTORCYCLE.
WHEN TOPPING OFF, PROTECT THE AREAS NEAR THE TANK WITH ABSORBENT MATERIAL.

Recommended products

AGIP BRAKE 4

Brake fluid

As an alternative to the recommended fluid, other fluids with performance equal to or higher than the

specifications may be used. Synthetic fluid SAE J1703, NHTSA 116 DOT 4, ISO 4925

Maintenance

ETX - STX 150

MAIN - 36

«
...
34
35
36
37
38
...
»

Содержание ETX 150











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETX 150

Бренд: Öhlins Страницы: 2

Mechatronics 35007-01

Бренд: Öhlins Страницы: 4

McPherson Strut MIR 5H02

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 4

Бренд: kellermann Страницы: 2

H-X-ADV-07-01-AL

Бренд: SRC Страницы: 6

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 88

TDM850'99 4TX-AE3

Бренд: Yamaha Страницы: 43

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 105

Бренд: Yamaha Страницы: 111

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 94

STRATOLINER XV19CTSC

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды