APRILIA ETX 150 Скачать руководство пользователя страница 38

Страница: 38 / 170

•

Tighten the nut (2), until the adjuster is

locked in place (3).

•

Check the clearance at the extremity of

the clutch lever.

•

Reposition the protective casing (1).

•

If the adjuster (3) is completely

screwed in, completely unscrewed,

and/or it is not possible to obtain the

correct clearance:

•

Slide the protective casing (1) out.

Completely screw in the nut (2) on the

adjuster (3).

•

Completely tighten the adjuster (3).

Operating from the right vehicle side:

•

Loosen the nut (4)

•

Turn the adjuster (5) until the clearance

at the extreme end of the clutch lever

is between 10 - 20 mm (0,39 - 0,79 in)

•

Tighten the nut (4), until the adjuster is

locked in place (5).

•

Check the clearance at the extremity of

the clutch lever.

•

Start the engine.

•

Completely activate the clutch, and in-

sert first gear.

•

Make sure that the engine does not

stop and that the vehicle does not

move forward, and that the friction

does not "slide" during acceleration or

during driving.

Headlight adjustment

NOTE

IN COMPLIANCE WITH LOCAL LEGISLATION, SPECIFIC PROCEDURES MUST BE FOLLOWED
WHEN ALIGNING THE LIGHTS.

Maintenance

ETX - STX 150

MAIN - 38

Содержание ETX 150











































































































































































Результаты поиска

Содержание ETX 150

Отзывы:

Похожие инструкции для ETX 150

Бренды по названию

Популярные бренды

APRILIA ETX 150, Руководство по обслуживанию станции

Результаты поиска

Содержание ETX 150

Отзывы:

Похожие инструкции для ETX 150

Бренды по названию

Популярные бренды