APRILIA ETX 150 Скачать руководство пользователя

Страница: 126 / 170

•

Remove the oil seal (7)

Checking the components

Stem

Check the sliding surface for scorings and/or scratches.

These scorings can be eliminated by rubbing them with wet sandpaper (grain 1).

If the scorings are deep, replace the stem.

Use a dial gauge to check that the stem bending is below the limit value.

If over the value, replace the stem.

CAUTION

A BENT STEM SHOULD NEVER BE STRAIGHTENED BECAUSE ITS STRUCTURE WOULD BE
WEAKENED AND USING THE VEHICLE MAY BECOME DANGEROUS.

Sleeve

Check that there are no damages and/or cracks; otherwise, replace it.

Spring

Check the spring is in good conditions.

Filling oil

•

Place the sleeve in vertical position in

a vice with protection shoes.

•

Press the stem in the sleeve. Place a

support under the sleeve to remain it

pressed.

•

Pour part of the fork oil inside the fork.

•

Wait some minutes to distribute the oil

in all channels.

•

Pour the remaining oil.

•

Carry out some pumping.

Characteristic

Oil for front fork ETX

Suspensions

ETX - STX 150

SUSP - 126

Содержание ETX 150











































































































































































Результаты поиска

Содержание ETX 150

Отзывы:

Похожие инструкции для ETX 150

Бренды по названию

Популярные бренды

APRILIA ETX 150, Руководство по обслуживанию станции

Результаты поиска

Содержание ETX 150

Отзывы:

Похожие инструкции для ETX 150

Бренды по названию

Популярные бренды