APRILIA ETX 150 Скачать руководство пользователя

Страница: 105 / 170

•

Remove the pin (2)

•

After having removed the piston, pro-

ceed with the removal of the top ring

(3), the central ring (4) and the oil scra-

per ring (5)

Checking the cylinder

•

All seal surfaces must be clean and flat.

•

Check cylinder internal surface for signs of abrasion and scratches. Also check the seal

surfaces for damages.

CAUTION

IF THE GROOVES ON THE CYLINDER LINER ARE EVIDENT, REPLACE THE CYLINDER AND
THE PISTON.

Checking the piston

•

Measure the piston skirt diameter (1)

with a micrometer (2=10mm - 0.39in

from the piston lower border).

•

Replace the cylinder, the piston and

the piston ring all together if not com-

plying with specifications.

Characteristic

Minimum piston diameter

61 +/- 0.05 mm (2.40 +/- 0.0020 in)

Maximum piston diameter

61.98 / 61.97 mm (2.44 / 2.43 in)

ETX - STX 150

Engine

ENG - 105

Содержание ETX 150











































































































































































Результаты поиска

Содержание ETX 150

Отзывы:

Похожие инструкции для ETX 150

Бренды по названию

Популярные бренды

APRILIA ETX 150, Руководство по обслуживанию станции

Результаты поиска

Содержание ETX 150

Отзывы:

Похожие инструкции для ETX 150

Бренды по названию

Популярные бренды