Aplex ARCDIS -107 Скачать руководство пользователя страница 50

Страница: 50 / 50

ARCDIS-1XX User Manual

Appendix C: Panel Mounting and VESA Mounting

The ARCDIS-1XX is designed to be panel-mounted and VESA mounted as shown in Picture. Just

carefully place the unit through the hole and tighten the given 10 screws from the rear to secure the

mounting.

Figure C: Panel mounting and VESA mounting

Notice

：

Tighten the mounting clip screws by hand until the gasket seal contacts the

mounting surface uniformly.
Tighten the mounting clips screws to a torque of 8 ~ 10 kgf-cm by using the

specified sequence, making sure not to overtighten.

*Tighten the mounting clips to the specified torque to provide a proper seal and to

prevent damage to the product. Aplex assumes no responsibility for water or

chemical damage to the product or other equipment within the enclosure due to

improper installation.

Содержание ARCDIS -107



















































Результаты поиска

Содержание ARCDIS -107

Отзывы:

Похожие инструкции для ARCDIS -107

Бренды по названию

Популярные бренды

Aplex ARCDIS -107, Руководство пользователя

Результаты поиска

Содержание ARCDIS -107

Отзывы:

Похожие инструкции для ARCDIS -107

Бренды по названию

Популярные бренды