ApenGroup AQUAKOND AKY, Руководство по установке и обслуживанию

Страница: 36 / 44

CONDENSATION BOILER
AQUAKOND AKY
36
code HC0048.01GB ed.B-1406
AKY
7. MODULATION BOARD PARAMETERS
The table below reports all accepted values for parameters in CPU-PLUS board for each model of boiler.
Parameters of CPU-SMART board Version 7.00.xx
PARAMETER AKY032 AKY034 AKY050 AKY070 DESCRIPTION
d0 2
Flame modulation: 2=NTC1; 5=0÷10Vdc; 7=Modbus (SmartControl &
PID)
d1 2 Type of appliance: 0=heater; 2=boiler; 5=PCH
d2 1 Remote lock outlet (Q1): 0=disabled; 1=enabled
d3 sec 1 Circulator delay ON (RL1): 0÷255
d4 sec 60 Burner delay OFF (RL1): 0÷255 (1=5 sec 60=300 sec)
d5 1 Flue control enabled (NTC3): 0=disabled; 1=enabled
d6 sec 15 Interval between turning off and on (OFF timer) 0÷255
d7 0 Lock counter reset: 0÷1
d8
0 0 1 1 Boiler antifreeze enabled (NTC1): 0=disabled; 1=enabled
d9 0 Shutters enabled: 0=disabled; Do not change
b1 rpm 150 145 147 135 Min value motor revs (PWM1): 90÷999 (1=10 RPM)
b2
rpm 720 555 660 680 Max value motor revs (PWM1): 90÷999 (1=10 RPM)
b3 rpm 420 260 385 445 Start-up value of motor revs (PWM1): 90÷999 (1=10 RPM)
b4 2 Divider of HALL signal: 2÷3
b5 rpm 50 F3x lock; # revs x10 (50=500 rpm): 0÷300
b6 sec 20 F3x lock; error holding time before F3x lock is issued: 0÷255
b7
sec 0 Pre-washing time at max power: 0÷255
b8 sec 5 Duration of flame stabilization (start-up) 0÷255
b9 sec 15 Furnace post-washing time (FAN ON) 0÷255
b10 % 5 Increase of motor revs in % every b11 sec: 1÷100
b11 sec 2 Time range for increase of motor revs: 1÷100
b12 % 30 % of FAN motor modulation in antifreeze mode: 30÷100
b13
pwm 65 Integral coefficient (ki_pwm) to calculate PWM1- (exA36):0÷249
b14 pem 45 Proportional coefficient (kp_pwm) to calculate PWM1- (exA37):0÷249
b15 sec 60 Time for flux control at start-up 0÷255
Control for NTC1 modulation sensor with D0=2; Limit if D0=5 or 7
S1
1 NTC1 sensor enabling: 0=disabled; 1=enabled
ST1 °C 72 (75) NTC1 set point: -10÷90 (72 for standard models - 75 for 00X0 models)
SP1 °C 4 Hysteresis SP1: 0÷10
XD1 % 40 Proportional band (4 to 100)
TN1 sec 5 Integral time: 1÷255
AC1 1
0=modulation only; 1=ON/OFF if D0=5 or 7, 0/10V modulation or
MODBUS
TH1 °C 82
Higher temperature limit for F51 lock enabling: 10÷95
autoreset if NTC1<TH1-15°C
0/10 Vdc Control - D0=5
H51 0
Enabled only with D0=5 (0/10V) 0=modulation only; 1=modulation and
ON/OFF
H52 V 0.5 OFF voltage, burner turns off if H51=1: 0÷10
H53 V 0.5 Voltage delta for burner ON
H54
sec 5 Lower input holding time: 0÷255
H55 sec 5 Higher input holding time: 0÷255