ApenGroup Aermax line Скачать руководство пользователя страница 22

Страница: 22 / 40

Page 22 code HG0109.12GB ed.C-1106 rev.12

APEN GROUP reserves the right to change products and documents as required.

WARM AIR HEATER SERIES RAPID

** using Ø80/100 male/female eccentric adapters code G15835-08-10

(to be ordered separately)
Terminals include:

• TC33-08-VC1 - Complete terminal, Ø 80/80 fittings - Centre distance 120

• TC33-10-VC2 - Complete terminal, Ø 100/100 fittings - Centre distance 140

This layout requires that fittings be moved from the back to the top of the

heater. For more details, see instructions below.

HG0103 C2 016

To disassemble:

1) Cut "A" covers from upper panel

2) Pull "C" flue pipe

3) Disassemble the intake joint "D"

4) Disassemble the flue joint "B"

5) Remove internal covers "E" installed one on burner casing

and the other over flue hood

How to assemble:

1) Install one "E" cover (and its seal) on the side hole of the

exchanger.

2) Install "B" flue junction on upper hole of the exchanger

3) Insert intake junction "D" on burner compartment

4) Cut to length "C" pipe and install it on "D" air junction

reaching same height as flue outlet

5) Install pre-cut covers "A" and their seals on the hole for

air intake

6) Install "E" cover without seal on back hole of the flue

Disassembling

Assembling

80/80->Ø125

100/100->Ø150

130/130->Ø200

HG0109.12_ET_012

HG0109.12_C2_009

C33 TYPE (ROOF)
Combustion circuit is sealed from the room. Pipes end outdoor with a
concentric terminal.

Max L1 + L2 of layout, terminal excluded

Term. Ø80/80

TC33-08-VC1

Term. Ø100/100 TC33-10-VC2

Pipes and elbows Ø80

Pipes and elbows Ø100

Model

meters

RA015

11 + 11

RA024

11 + 11

RA032

10 + 10

RA035

9 + 9

RA043

7 + 7

RA054

4,5 + 4,5

10 + 10**

REMARK: Max possible length was equally divided between intake and discharge. Different ratios

are allowed, provided the maximum value shown in the table is not exceeded.

Содержание Aermax line









































Результаты поиска

Содержание Aermax line

Отзывы:

Похожие инструкции для Aermax line

Бренды по названию

Популярные бренды

ApenGroup Aermax line, Руководство пользователя по установке и обслуживанию

Результаты поиска

Содержание Aermax line

Отзывы:

Похожие инструкции для Aermax line

Бренды по названию

Популярные бренды