ApenGroup Aermax line Скачать руководство пользователя страница 13

Страница: 13 / 40

Page 13

APEN GROUP reserves the right to change products and documents as required.

code HG0109.12GB ed.C-1106 rev.12

WARM AIR HEATER SERIES RAPID

Burner lock:

If the flame control device detects an ignition failure of the burner,

the start-up cycle is automatically repeated up to 4 times. If the

lock continues, the red LED on the front of the heater turns on.

Safety thermostat locked (STB):

A safety thermostat (STB) for each cooling fan is installed on

the heater.

The STB thermostat is a safety device that triggers if a fault

occurs. Thermostat is automatically reset by AGP card. When

the STB thermostat triggers, the red LED on the front of the

heater is lit (the same as for burner lock).

Diagnostics

To find out the reason of the lock, refer to

"Diagnostics"

section

in paragraph 7.

SUMMER : operation in ventilation mode

The heater can be used also in summer to have air flow in

the room.

To enable summer ventilation, turn I/O/II switch on “II = Summer”.

REMARK:

If you want to remotely control the Sum-

mer/Winter mode, please leave the switch on the heater

turned on Winter [ pos. I ].

If you power off the unit before cooling cycle is completed

and then power it on again, fans star immediately.

HG0100 C2 012

4.3 Accessories

To ease the use of the heater, APEN can supply two accessories

that allow to remotely control heater's commands.

Available commands are described below. Please refer to

the "instructions to the installer" section for electrical wiring

instructions.

Remote Control G12800

G12800 remote control includes ON/OFF [0/I] command, sum-

mer/winter switch, and reset button.

You do not power off the unit by turning the 0/I switch off. You

simply have the flame extinguished while the exchanger is

properly cooled down.

However it is necessary to reset the safety thermostat (STB) is

on the remote control.

Remote control code G00094

This command enables to:

- Set room temperature

- Switch Summer/Winter operation

- Turn off the heater without powering it down

- Display burner lock

- Reset the burner

With this command too, the only way to reset the safety thermostat

(STB) is on the remote control.

HG0107.08_C2_005 IT

Содержание Aermax line









































Результаты поиска

Содержание Aermax line

Отзывы:

Похожие инструкции для Aermax line

Бренды по названию

Популярные бренды

ApenGroup Aermax line, Руководство пользователя по установке и обслуживанию

Результаты поиска

Содержание Aermax line

Отзывы:

Похожие инструкции для Aermax line

Бренды по названию

Популярные бренды