ApenGroup Aermax line Скачать руководство пользователя страница 23

Страница: 23 / 40

Page 23

APEN GROUP reserves the right to change products and documents as required.

code HG0109.12GB ed.C-1106 rev.12

WARM AIR HEATER SERIES RAPID

5.5

Electrical Wiring

HG0109.12_C2_005

Room Thermostat Wiring

It is mandatory to install a room thermostat or a timer to turn

the burner off without powering off the unit.

No spare jumper

supplied with the heater.

Connect the thermostat to terminals No. 34 and 35 of the

board on the electronic card installed into the control panel

housing of RAPID heater (it replaces the jumper, see diagram

in this page).

If the burner can be turned off by multiple switches, they must

be wired in series.

A remote button can be installed and wired to terminals No.

29 and 30 of the board [WARNING: current is 230V].

The type of the button must be Normally Open.

Power Supply

The heater shall be properly wired to an efficient grounding

system, complying with existing regulations.

Single-phase 230 Vac supply with neutral. Do not mistake

neutral and phase wires If phase and neutral wires are

exchanged, the unit will automatically lock.

The heater can be plugged into mains using a plug-socket

only if the latter prevents any mistake between phase and

neutral wires.

The system wire gauge in general, and cable section in parti-

cular, must suit the unit rated input (see technical data table).

Keep cables far from heat sources.

REMARK: A multipole cut-out switch must be installed

before the heater with suitable electric protection.

The section of supply cables must be at least 1.5 mm²

The unit shall be plugged into the mains using the plug sup-

plied. Always unplug the unit during maintenance operations.

Reset button

Summer Ventilation

You can enable only the fans (summer ventilation while the

burner is off) in the following ways:

1) Turn the switch on the heater on

" =SUMMER". In this way, the fans can be turned on or

off by rotating the switch or by powering off the appliance (this

latter is not allowed in Winter mode).

2) Use remote control - see G12800 and G00094 accessories

3) Remotely control the CN3 connector command through

terminals No. 34,35, and 36 as indicated in the wiring diagram

for G12800 accessory [see diagram in the following page].

When the summer ventilation command is remotely controlled,

the switch on the heater shall be turned on " =WINTER".

HG0109.09_C2_007

Summer /0 /Winter switch

HG0109.12 C2 001

RESET

ROOM

THERMOSTAT

Содержание Aermax line









































Результаты поиска

Содержание Aermax line

Отзывы:

Похожие инструкции для Aermax line

Бренды по названию

Популярные бренды

ApenGroup Aermax line, Руководство пользователя по установке и обслуживанию

Результаты поиска

Содержание Aermax line

Отзывы:

Похожие инструкции для Aermax line

Бренды по названию

Популярные бренды