background image

4

TC5-1V10SA  rev.06

The TC5-1V10SA is an electronic device used for environmental control in
livestock buildings.  It allows the user to maintain a specified target tem-
perature by controlling the operation of ventilation and heating equipment.
One stage of variable speed fans can be connected to the controller, as
well as eight stages of constant-speed fans and two stages of either con-
stant-speed fans or heating units. In addition, one of the constant-speed
fan stages can be configured as a mist cooling stage.

The main features of the TC5-1V10SA are as follows:

THREE-DIGIT DISPLAY

A three-digit display provides a high level of accuracy, allowing the user to
specify a temperature to within one tenth of a degree (in Fahrenheit or
Celsius units).

PILOT LIGHTS

Pilot lights indicating the state of outputs allow the user to monitor the
operation of the system without having to enter the building.

MINIMUM VENTILATION CYCLE

When ventilation is not required for cooling, the first stage fans can be
operated either continuously or intermittently to reduce the level of humid-
ity and supply oxygen to the room.

TEMPERATURE AND MINIMUM VENTILATION SPEED CURVES

The controller can be set to automatically change the temperature set point
and the minimum ventilation speed over a given period of time in accor-
dance with the user's requirements by specifying a temperature curve and
a minimum ventilation speed curve with up to six different points each.

CHOICE OF TEN MOTOR CURVES

The variation in motor speed resulting from a change in voltage will depend
on the make and capacity of the motor.  In order to achieve a high degree
of compatibility between controller and motor, the user can choose from
among ten different motor curves, thus ensuring that the correct voltage is
supplied.

ZONED OR CASCADING HEATERS

FEATURES

Содержание TC5-1V10SA




























































Отзывы: