Antunes 9100618 Скачать руководство пользователя страница 7

Страница: 7 / 28

CHEESE MELTER

P/N 1010983 Rev. F 05/19

Unpacking

1. Remove unit and all packing materials from

shipping carton.

2. Open the box. It should contain the follow-

ing items:

• Cheese Melter

• Water Drip Tray

• Water Hookup Kit

• Information Packet

3. Remove information packet.

4. Remove all packing materials and protective

coverings from the unit.

5. Wash all removable parts (Spatula and

Water Drip Tray) in soap and water. Rinse

with clean hot water and allow to air dry.

6. Wipe all surfaces of the unit with a hot damp

cloth.

NOTE: Do NOT use a dripping wet cloth.

Wring out before use.

7. Re-install all removed parts.

INSTALLATION

CAUTION

All electrical connections must be in accordance

with local electrical codes and any other appli-

cable codes.

WARNING

ELECTRICAL SHOCK HAZARD.

FAILURE TO FOLLOW THE INSTRUCTIONS IN

THIS MANUAL COULD RESULT IN SERIOUS

INJURY OR DEATH.

• Electrical ground is required on this appliance.
• Do NOT modify the power supply cord plug. If

it does not fit the outlet, have a proper outlet

installed by a qualified electrician.

• Do NOT use an extension cord with this appliance.
• The unit should be grounded according to local

electrical codes to prevent the possibility of electri-

cal shock. It requires a grounded receptacle with

separate electrical lines, protected by fuses or

circuit breaker of the proper rating.

• Check with a qualified electrician if you are unsure

if the appliance is properly grounded.

Содержание 9100618





























Результаты поиска

Содержание 9100618

Отзывы:

Бренды по названию

Популярные бренды

Antunes 9100618, Руководство пользователя

Результаты поиска

Содержание 9100618

Отзывы:

Бренды по названию

Популярные бренды