manualshive.com logo in svg

Antunes 9100618, Руководство пользователя

Поделиться
Скачать
Antunes 9100618 Скачать руководство пользователя страница 22

CHEESE MELTER

22

P/N 1010983 Rev. F 05/19

®

Problem

Possible Cause

Corrective Action

Steam from Generator 

is reduced compared to 

former operation.

Restrictor Tube and/or Generator Tubes 

are clogged.

Clean Restrictor Tube and/or Generator 

Tubes.

Water pump solenoid is inoperable.

Contact your maintenance person or 

Authorized Service Agency.

The unit was not allowed enough time to 

preheat.

Remove excess water from the genera-

tor casting. Allow 20 minutes to preheat 

before operating. Do NOT operate the 

unit during preheat cycle.

Inoperable heater relay.

Contact your maintenance person or  

Authorized Service Agency.

The Control Board setpoint temperature 

is set too low.

Surface temperature of the casting 

should be between 375°–425°F (191°– 

218°C) when the red light on the control 

board turns off. If the temp is too low, 

contact your maintenance person or 

Authorized Service Agency.

Heavy deposit buildup on the Generator.

Clean the Generator according to the 

procedures in the Maintenance section 

of this manual.

Unit floods or is always 

steaming. Power on, 

solenoid makes a chat-

tering noise.

or

Unit floods overnight. 

Power off. 

Water leaking in the  

electrical housing.

Unit heats up, pump or 

solenoid valve works with 

the momentary switch 

but will not steam during 

timer cycles.

Incorrect water pressure.

*(Regulated units only.) Set water  

pressure to 20 psi (138 kPa).

Solenoid Valve inoperable.

Clean or replace Solenoid Valve. 

Contact your maintenance person or 

Authorized Service Agency.

Control Board is not programmed  

properly.

Verify programming as described in the 

Programming section of this manual.

Control Board is inoperable.

Contact your maintenance person or 

Authorized Service Agency.

Pin hole leak in the hoses.

Replace the hoses.

Water pump impeller is cracked or 

damaged.

Contact your maintenance person or 

Authorized Service Agency.

Inlet Tube or Restrictor Tube is loose.

Tighten the loose fittings.

Generator Tube is loose or damaged.

Tighten the loose fittings or contact 

your maintenance person or Authorized 

Service Agency.

TROUBLESHOOTING (continued)

Содержание 9100618





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды