manualshive.com logo in svg

Antunes 9100618, Руководство пользователя

Поделиться
Скачать
Antunes 9100618 Скачать руководство пользователя страница 11

11

CHEESE MELTER

P/N 1010983 Rev. F 05/19

®

PROGRAMMING (continued)

  2.  Press the button highlighted below to change 

the control from Operation to Program mode.  

“CYC” is displayed momentarily.  Then press 

an Operating Button to change that button’s 

settings.

CYC

NOTE:  If no change is made within 10 seconds 

at any time during the programming process, 

all changes made up to that point are stored in 

memory and the control reverts to Operation 

mode.

  3.  The unit displays the current setting for total 

cycle time in minutes. Use the buttons high-

lighted below to change this setting.

00

  4.  Press the highlighted button below to accept 

the total cycle time in minutes on the display.

00

  5.  The unit then displays the current setting for 

total cycle time in seconds. Use the buttons 

highlighted below to change this setting.

     21

  6.  Press the highlighted button below to accept 

the total cycle time in seconds on the display.

     21

Содержание 9100618





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды